10H116 datasheet(2/5 Pages) ONSEMI

2 / 5 page

MC10H116

www.onsemi.com

Table 1. MAXIMUM RATINGS

Symbol

Characteristic

Rating

Unit

VEE

Power Supply (VCC = 0)

−8.0 to 0

Vdc

Input Voltage (VCC = 0)

0 to VEE

Vdc

Iout

Output Current

Continuous

Surge

100

Operating Temperature Range

0 to +75

°C

Tstg

Storage Temperature Range

Plastic

Ceramic

−55 to +150

−55 to +165

°C

Stresses exceeding those listed in the Maximum Ratings table may damage the device. If any of these limits are exceeded, device functionality

should not be assumed, damage may occur and reliability may be affected.

Table 2. ELECTRICAL CHARACTERISTICS (VEE = −5.2 V ±5%) (Note 2)

0°

25°

75°

Symbol

Characteristic

Min

Max

Min

Max

Min

Max

Unit

Power Supply Current

−

IinH

Input Current High

−

150

−

ICBO

Input Leakage Current

−

1.5

−

1.0

−

1.0

VBB

Reference Voltage

−1.38

−1.27

−1.35

−1.25

−1.31

−1.19

Vdc

VOH

High Output Voltage

−1.02

−0.84

−0.98

−0.81

−0.92

−0.735

Vdc

VOL

Low Output Voltage

−1.95

−1.63

−1.95

−1.63

−1.95

−1.60

Vdc

VIH

High Input Voltage (Note 1)

−1.17

−0.84

−1.13

−0.81

−1.07

−0.735

Vdc

VIL

Low Input Voltage (Note 1)

−1.95

−1.48

−1.95

−1.48

−1.95

−1.45

Vdc

VCMR

Common Mode

Range (Note 4)

−

−2.85 to −0.8

−

Vdc

VPP

Input Sensitivity (Note 3)

−

150 typ

−

mVPP

1. When VBB is used as the reference voltage.

2. Each MECL 10H™ series circuit has been designed to meet the specifications shown in the test table, after thermal equilibrium has been

established. The circuit is in a test socket or mounted on a printed circuit board and transverse air flow greater than 500 lfpm is maintained.

Outputs are terminated through a 50 ohm resistor to −2.0 V.

3. Differential input not to exceed 1.0 Vdc.

4. 150 mVp−p differential input required to obtain full logic swing on output.

Table 3. AC CHARACTERISTICS

0°

25°

75°

Symbol

Characteristic

Min

Max

Min

Max

Min

Max

Unit

tpd

Propagation Delay

0.4

1.3

0.4

1.3

0.45

1.45

Rise Time

0.5

1.5

0.5

1.6

0.5

1.7

Fall Time

0.5

1.5

0.5

1.6

0.5

1.7

NOTE: Device will meet the specifications after thermal equilibrium has been established when mounted in a test socket or printed circuit

board with maintained transverse airflow greater than 500 lfpm. Electrical parameters are guaranteed only over the declared

operating temperature range. Functional operation of the device exceeding these conditions is not implied. Device specification limit

values are applied individually under normal operating conditions and not valid simultaneously.

10H116 bảng dữ liệu(PDF) 2 Page - ON Semiconductor

10H116 bảng dữ liệu(HTML) 2 Page - ON Semiconductor

Html Pages

1 2 3 4 5

bảng dữ liệu tải về

Link URL