RN1723 datasheet(18/32 Pages) MICROCHIP

18 / 32 page

RN1723

DS70005224A-page 18

 2015 Microchip Technology Inc.

4.1.2

RF EXPOSURE

All transmitters regulated by FCC must comply with RF

exposure requirements. KDB 447498 General RF

Exposure Guidance provides guidance in determining

whether proposed or existing transmitting facilities,

operations or devices comply with limits for human

exposure to Radio Frequency (RF) fields adopted by

the Federal Communications Commission (FCC).

From the FCC Grant: Modular approval. Output power

listed is conducted. This module may only be installed

by the OEM or an OEM integrator. Only antenna(s)

documented in this filing may be used with this trans-

mitter. The antenna(s) used for this transmitter must be

installed to provide a separation distance of at least 20

cm from all persons and must not be collocated or

operating in conjunction with any other antenna or

transmitter within a host device, except in accordance

with FCC multi-transmitter product procedures. OEM

integrators and End-users and installers must be pro-

vided with antenna installation instructions and trans-

mitter operating conditions for satisfying RF exposure

compliance.

4.1.3

APPROVED EXTERNAL ANTENNA

TYPES

To maintain modular approval in the United States,

only the antenna types that have been tested shall

be used. It is permissible to use different antenna

manufacturers provided the same antenna type that

has

similar

in-band

and

out-of-band

radiation

patterns and antenna gain (equal to or less than) is

used.

Modular approval testing of the RN1723 module was

performed with the antenna types listed in Table 3-1.

4.1.4

HELPFUL WEB SITES

• Federal Communications Commission (FCC):

http://www.fcc.gov

• FCC Office of Engineering and Technology (OET)

Laboratory Division Knowledge Database (KDB):

http://apps.fcc.gov/oetcf/kdb/index.cfm

4.2

Canada

The RN1723 module has been certified for use in

Canada under Industry Canada (IC) Radio Standards

Specification (RSS) RSS-210 and RSSGen. Modular

approval permits the installation of a module in a

host device without the need to recertify the device.

4.2.1

LABELING AND USER

INFORMATION REQUIREMENTS

Labeling Requirements for the Host Device (from

Section 3.2.1, RSS-Gen, Issue 3, December 2010):

The host device shall be properly labeled to identify

the module within the host device.

The Industry Canada certification label of a module

shall be clearly visible at all times when installed in

the host device, otherwise the host device must be

labeled to display the Industry Canada certification

number of the module, preceded by the words

“Contains

transmitter

module”,

the

word

“Contains”, or similar wording expressing the same

meaning, as follows:

User

Manual

Notice

for

License-Exempt

Radio

Apparatus (from Section 7.1.3 RSS-Gen, Issue 3,

December 2010): User manuals for license-exempt

radio

apparatus

shall

contain

the

following

equivalent notice in a conspicuous location in the

user manual or alternatively on the device or both:

Transmitter Antenna (from Section 7.1.2 RSS-Gen,

Issue

December

2010):

User

manuals

for

transmitters shall display the following notice in a

conspicuous location:

The above notice may be affixed to the device instead

of displayed in the user manual.

Contains transmitter module IC: 7693A-RN1723

This

device

complies

with

Industry

Canada

license-exempt

RSS

standard(s).

Operation

subject to the following two conditions: (1) this

device may not cause interference, and (2) this

device must accept any interference, including

interference that may cause undesired operation of

the device.

Le présent appareil est conforme aux CNR d'Indus-

trie Canada applicables aux appareils radio exempts

de licence. L'exploitation est autorisée aux deux

conditions suivantes: (1) l'appareil ne doit pas

produire de brouillage, et (2) l'utilisateur de l'appareil

doit accepter tout brouillage radioélectrique subi,

même

brouillage

est

susceptible

d'en

compromettre le fonctionnement.

Under Industry Canada regulations, this radio

transmitter may only operate using an antenna of

a type and maximum (or lesser) gain approved for

the transmitter by Industry Canada. To reduce

potential radio interference to other users, the

antenna type and its gain should be so chosen

that the equivalent isotropically radiated power

(e.i.r.p.) is not more than that necessary for

successful communication.

Conformément

réglementation

d'Industrie

Canada, le présent émetteur radio peut fonctionner

avec une antenne d'un type et d'un gain maximal (ou

inférieur) approuvé pour l'émetteur par Industrie

Canada. Dans le but de réduire les risques de

brouillage radioélectrique à l'intention des autres

utilisateurs, il faut choisir le type d'antenne et son

gain de sorte que la puissance isotrope rayonnée

équivalente (p.i.r.e.) ne dépasse pas l'intensité

nécessaire à l'établissement d'une communication

satisfaisante.

RN1723 bảng dữ liệu(PDF) 18 Page - Microchip Technology

RN1723 bảng dữ liệu(HTML) 18 Page - Microchip Technology

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32

bảng dữ liệu tải về

Link URL