LM319AM datasheet(2/11 Pages) NSC

2 / 11 page

Absolute Maximum Ratings (Note 8)

If Military/Aerospace specified devices are required,

please contact the National Semiconductor Sales Office/

Distributors for availability and specifications.

Total Supply Voltage

36V

Output to Negative Supply Voltage

36V

Ground to Negative Supply Voltage

25V

Ground to Positive Supply Voltage

18V

Differential Input Voltage

±5V

Input Voltage (Note 2)

±15V

ESD rating (1.5 k

Ω in series with

100 pF)

800V

Power Dissipation (Note 3)

500 mW

Output Short Circuit Duration

10 sec

Storage Temperature Range

−65˚C to 150˚C

Lead Temperature

(Soldering, 10 sec.)

260˚C

Soldering Information

Dual-In-Line Package

Soldering (10 seconds)

260˚C

Small Outline Package

Vapor Phase (60 seconds)

215˚C

Infrared (15 seconds)

220˚C

See AN-450 “Surface Mounting Methods and Their Effect

on Product Reliability” for other methods of soldering

surface mount devices.

Operating Temperature Range

LM119

−55˚C to 125˚C

LM219

−25˚C to 85˚C

Electrical Characteristics (Note 4)

Parameter

Conditions

LM119/LM219

Units

Min

Typ

Max

Input Offset Voltage (Note 5)

A = 25˚C, RS ≤ 5k

0.7

4.0

Input Offset Current (Note 5)

A = 25˚C

Input Bias Current

A = 25˚C

150

500

Voltage Gain

A = 25˚C (Note 7)

V/mV

Response Time (Note 6)

A = 25˚C, VS = ±15V

Saturation Voltage

IN ≤ −5 mV, IOUT = 25 mA

A = 25˚C

0.75

1.5

Output Leakage Current

IN ≥ 5 mV, VOUT = 35V

A = 25˚C

0.2

µA

Input Offset Voltage (Note 5)

S ≤ 5k

Input Offset Current (Note 5)

100

Input Bias Current

1000

Input Voltage Range

S = ±15V

−12

±13

+12

+ = 5V, V− = 01

Saturation Voltage

≥ 4.5V, V− = 0

IN ≤ −6 mV, ISINK ≤ 3.2 mA

A ≥ 0˚C

0.23

0.4

A ≤ 0˚C

0.6

Output Leakage Current

IN ≥ 5 mV, VOUT = 35V,

µA

− = V

GND = 0V

Differential Input Voltage

±5V

Positive Supply Current

A = 25˚C, V

+ = 5V, V− = 0

4.3

Positive Supply Current

A = 25˚C, VS = ±15V

11.5

Negative Supply Current

A = 25˚C, VS = ±15V

4.5

Note 2: For supply voltages less than ±15V the absolute maximum input voltage is equal to the supply voltage.

Note 3: The maximum junction temperature of the LM119 is 150˚C, while that of the LM219 is 110˚C. For operating at elevated temperatures, devices in the H10

package must be derated based on a thermal resistance of 160˚C/W, junction to ambient, or 19˚C/W, junction to case. The thermal resistance of the J14 and N14

packages is 100˚C/W, junction to ambient.

Note 4: These specifications apply for VS = ±15V, and the Ground pin at ground, and −55˚C ≤ TA ≤ +125˚C, unless otherwise stated. With the LM219, however, all

temperature specifications are limited to −25˚C

≤ TA ≤ +85˚C. The offset voltage, offset current and bias current specifications apply for any supply voltage from a

single 5V supply up to ±15V supplies. Do not operate the device with more than 16V from ground to VS.

Note 5: The offset voltages and offset currents given are the maximum values required to drive the output within a volt of either supply witha1mA load. Thus, these

parameters define an error band and take into account the worst case effects of voltage gain and input impedance.

Note 6: The response time specified (see definitions) is for a 100 mV input step with 5 mV overdrive.

Note 7: Output is pulled up to 15V through a 1.4 k

Ω resistor.

Note 8: Refer to RETS119X for LM119H/883 and LM119J/883 specifications.

LM319AM bảng dữ liệu(PDF) 2 Page - National Semiconductor (TI)

LM319AM bảng dữ liệu(HTML) 2 Page - National Semiconductor (TI)

Html Pages

1 2 3 4 5 6 7 8 9 10 11

bảng dữ liệu tải về

Link URL