| công cụ tìm kiếm bảng dữ liệu linh kiện điện tử |
|
TMP320C6701GLWA100 bảng dữ liệu(PDF) 13 Page - Texas Instruments |
|
|
|||||||||||||||||||||||||||||
TMP320C6701GLWA100 bảng dữ liệu(HTML) 13 Page - Texas Instruments |
|
13 / 70 page ![]() TMS320C6205 FIXED-POINT DIGITAL SIGNAL PROCESSOR SPRS106E − OCTOBER 1999 − REVISED MARCH 2004 13 POST OFFICE BOX 1443 • HOUSTON, TEXAS 77251−1443 Signal Descriptions SIGNAL TYPE† DESCRIPTION NAME NO. TYPE† DESCRIPTION CLOCK/PLL CLKIN J3 I Clock Input CLKOUT2 T19 O Clock output at half of device speed DUsed for synchronous memory interface CLKMODE0 L3 I Clock mode select 0 DSelects whether the on-chip PLL is used or bypassed. For more details, see the Clock PLL section. DThe PLL Multiply Factor is selected at boot configuration. For more details, see the EMIF − Data pin descriptions and the clock PLL section. PLLV‡ K5 A§ PLL analog VCC connection for the low-pass filter PLLG‡ L2 A§ PLL analog GND connection for the low-pass filter PLLF‡ L1 A§ PLL low-pass filter connection to external components and a bypass capacitor JTAG EMULATION TMS E17 I JTAG test-port mode select (features an internal pullup) TDO D19 O/Z JTAG test-port data out TDI D18 I JTAG test-port data in (features an internal pullup) TCK D17 I JTAG test-port clock TRST C19 I JTAG test-port reset (features an internal pulldown) EMU1 E18 I/O/Z Emulation pin 1, pullup with a dedicated 20-kΩ resistor¶ EMU0 F15 I/O/Z Emulation pin 0, pullup with a dedicated 20-kΩ resistor¶ RESET AND INTERRUPTS RESET C3 I Device reset NMI A8 I Nonmaskable interrupt DEdge-driven (rising edge) EXT_INT7 B15 EXT_INT6 C15 I External interrupts Ed d i EXT_INT5 A16 I DEdge-driven DPolarity independently selected via the External Interrupt Polarity Register bits (EXTPOL [3:0]) EXT_INT4 B16 DPolarity independently selected via the External Interrupt Polarity Register bits (EXTPOL.[3:0]) IACK A15 O Interrupt acknowledge for all active interrupts serviced by the CPU INUM3 F12 INUM2 A14 O Active interrupt identification number V lid d i IACK f ll i i ( j l) INUM1 B14 O DValid during IACK for all active interrupts (not just external) DEncoding order follows the interrupt-service fetch-packet ordering INUM0 C14 DEncoding order follows the interrupt-service fetch-packet ordering POWER-DOWN STATUS PD B18 O Power-down modes 2 or 3 (active if high) † I = Input, O = Output, Z = High Impedance, S = Supply Voltage, GND = Ground ‡ PLLV, PLLG, and PLLF are not part of external voltage supply or ground. See the clock PLL section for information on how to connect these pins. § A = Analog Signal (PLL Filter) ¶ For emulation and normal operation, pull up EMU1 and EMU0 with a dedicated 20-kΩ resistor. For boundary scan, pull down EMU1 and EMU0 with a dedicated 20-kΩ resistor. |
|
Link URL |
| Cho đến nay ALLDATASHEET có giúp ích cho doanh nghiệp của bạn hay không? [ DONATE ] |
Alldatasheet là | Quảng cáo | Liên lạc với chúng tôi | Chính sách bảo mật | Liên kết đến bảng dữ liệu | Trao đổi link | Tìm kiếm theo nhà sản xuất All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |