PT6220 datasheet(3/7 Pages) TI1

3 / 7 page

For assistance or to order, call (800) 531-5782

Power Trends, Inc. 27715 Diehl Road, Warrenville, IL 60555 (800) 531-5782 Fax: (630) 393-6902 http://www.powertrends.com

Application

Notes

PT6100/6120/6210/6220/6300/6320 Series

Adjusting the Output Voltage of Power Trends’

Wide Input Range Bus ISRs

The output voltage of the Power Trends’ Wide Input Range

Series ISRs may be adjusted higher or lower than the factory

trimmed pre-set voltage with the addition of a single external

resistor. Table 1 accordingly gives the allowable adjustment

range for each model for either series as Va (min) and Va (max).

Adjust Up:

An increase in the output voltage is obtained by

adding a resistor R2, between pin 12 (Vo adjust) and pins 5-8

(GND).

Adjust Down:

Add a resistor (R1), between pin 12 (Vo adjust)

and pins 9-11(Vout).

Refer to Figure 1 and Table 2 for both the placement and value

of the required resistor; either (R1) or R2 as appropriate.

Notes:

1. Use only a single 1% resistor in either the (R1) or R2 loca-

tion. Place the resistor as close to the ISR as possible.

2. Never connect capacitors from Vo adjust to either GND or

Vout. Any capacitance added to the Vo adjust pin will affect

the stability of the ISR.

4. Adjustments to the output voltage may place additional

limits on the maximum and minimum input voltage for the

part. The revised maximum and minimum input voltage

limits must comply with the following requirements. Note

that the minimum input voltage limits are also model depen-

dant.

Vin (max) = (8 x Va)V or *30/38V,

whichever is less.

*Limit is 30V when inhibit function is active.

PT6x0x/PT6x1x series:

Vin (min) = (Va + 4)V or 9V,

whichever is greater.

PT6x2x series:

Vo <10V;

Vin (min) = (Va + 2.0)V or 7.0V,

whichever is greater.

Vo ≥10V;

Vin (min) = (Va + 2.5)V

Figure 1

The values of (R1) [adjust down], and R2 [adjust up], can

also be calculated using the following formulae.

Ro (Va – 1.25)

(R1)

Vo – Va

kΩ

1.25 Ro

kΩ

Va – Vo

Where: Vo = Original output voltage

Va = Adjusted output voltage

Ro = The resistance value fromTable 1

Table 1

ISR ADJUSTMENT RANGE AND FORMULA PARAMETERS

1Adc Rated

PT6102

PT6101

PT6103

PT6122

PT6121

2Adc Rated

PT6213

PT6212

PT6214

PT6223

PT6222

3Adc Rated

PT6303

PT6302

PT6304

PT6323

PT6322

Vo (nom)

3.3

5.0

12.0

Va (min)

1.89

1.88

2.18

2.43

Va (max)

6.07

11.25

8.5

22.12

Ro (k

Ω

Ω)

66.5

150.0

90.9

243.0

Adjust Up

µF Ceramic

(Optional)

100

µF

(Req'd)

COM

Vin

(R1)

Adj Down

PT6100/6200/6300

9,10,11

5,6,7,8

2,3,4

Vin

V o

G N D

Vo(adj)

More Application Notes

PT6220 bảng dữ liệu(PDF) 3 Page - Texas Instruments

PT6220 bảng dữ liệu(HTML) 3 Page - Texas Instruments

Html Pages

1 2 3 4 5 6 7

bảng dữ liệu tải về

Link URL