| công cụ tìm kiếm bảng dữ liệu linh kiện điện tử |
|
OPA698 bảng dữ liệu(PDF) 4 Page - Texas Instruments |
|
|
|
|||||||||||||||||||||||||||||
OPA698 bảng dữ liệu(HTML) 4 Page - Texas Instruments |
|
4 / 27 page ![]() OPA698 4 SBOS258B www.ti.com OUTPUT VOLTAGE LIMITERS (Cont.) Limited Step Response 2x Overdrive Overshoot VIN = 0 to ±2V Step 250 mV typ C Recovery Time VIN = ±2V to 0V Step 1 1.9 2 2.1 ns max B Linearity Guardband(9) f = 5MHz, VO = 2VPP 30 mV typ C THERMAL CHARACTERISTICS Temperature Range Specification: I –40 to +85 °C typ C Thermal Resistance Junction-to-Ambient DSO-8 125 ——— °C/W typ C NOTES: (1) Junction temperature = ambient for +25 °C specifications. (2) Junction temperature = ambient at low temperature limit; junction temperature = ambient +23 °C at high temperature limit for over temperature specifications. (3) Test levels: (A) 100% tested at +25 °C. Over temperature limits by characterization and simulation. (B) Limits set by characterization and simulation. (C) Typical value only for information. (4) Current is considered positive out of node. (5) CMIR tested as < 3dB degradation from minimum CMRR at specified limits. (6) IVH (VH bias current) is positive, and IVL (VL bias current) is negative, under these conditions. See Note 3, Figure 1, and Figure 8. (7) Limiter feedthrough is the ratio of the output magnitude to the sinewave added to VH (or VL) when VIN = 0. (8) VH slew rate conditions are: VIN = +2V, G = +2, VL = –2V, VH = step between 2V and 0V. VL slew rate conditions are similar. (9) Linearity Guardband is defined for an output sinusoid (f = 5MHz, VO = 0VDC ± 1VPP) centered between the limiter levels (VH and VL). It is the difference between the limiter level and the peak output voltage where SFDR decreases by 3dB (see Figure 9). ELECTRICAL CHARACTERISTICS: VS = ±5V (Cont.) Boldface limits are tested at +25 °C. G = +2, RF = 402Ω, RL = 500Ω, and VH = –VL = 2V (see Figure 1 for AC performance only), unless otherwise noted. OPA698ID TYP MIN/MAX OVER TEMPERATURE 0 °C to –40 °C to MIN/ TEST PARAMETER CONDITIONS +25 °C +25 °C(1) +70°C(2) +85°C(2) UNITS MAX LEVEL(3) |
|
Link URL |
| Cho đến nay ALLDATASHEET có giúp ích cho doanh nghiệp của bạn hay không? [ DONATE ] |
Alldatasheet là | Quảng cáo | Liên lạc với chúng tôi | Chính sách bảo mật | Liên kết đến bảng dữ liệu | Trao đổi link | Tìm kiếm theo nhà sản xuất All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |