| công cụ tìm kiếm bảng dữ liệu linh kiện điện tử |
|
UCD2003B bảng dữ liệu(PDF) 12 Page - Texas Instruments |
|
|
|||||||||||||||||||||||||||||
UCD2003B bảng dữ liệu(HTML) 12 Page - Texas Instruments |
|
12 / 24 page ![]() ( ) J(MAX) A (MAX) JA T T PD - = q N D OLi Li i 1 P V I = = ´ å 12 ULN2003B SLRS064B – JUNE 2014 – REVISED AUGUST 2016 www.ti.com Product Folder Links: ULN2003B Submit Documentation Feedback Copyright © 2014–2016, Texas Instruments Incorporated Typical Application (continued) (1) These test conditions can not be run simultaneously. 9.2.1 Design Requirements For this design example, use the parameters listed in Table 1 as the input parameters. Table 1. Design Parameters DESIGN PARAMETER (1) EXAMPLE VALUE GPIO Voltage 3.3 V or 5 V Coil Supply Voltage 12 V to 48 V Number of Channels 7 Output Current (RCOIL) 20 mA to 300 mA per channel (See Figure 5) Duty Cycle See Figure 6 to Figure 14 9.2.2 Detailed Design Procedure When using ULN2003B in a coil driving application, determine the following: • Input Voltage Range • Temperature Range • Output and Drive Current • Power Dissipation 9.2.2.1 Drive Current The coil current is determined by the coil voltage (VSUP), coil resistance and output low voltage (VOL or VCE(SAT)). ICOIL = (VSUP – VCE(SAT)) / RCOIL (1) 9.2.2.2 Output Low Voltage The output low voltage (VOL) is the same thing as VCE(SAT) and can be determined by, Figure 1, Figure 2, or Figure 4. 9.2.2.3 Power Dissipation and Temperature The number of coils driven is dependent on the coil current and on-chip power dissipation. The number of coils driven can be determined by Figure 6 or Figure 7. For a more accurate determination of number of coils possible, use Equation 2 to calculate ULN2003B on-chip power dissipation PD: where • N is the number of channels active together. • VOLi is the OUTi pin voltage for the load current ILi. This is the same as VCE(SAT) (2) In order to guarantee reliability of ULN2003B and the system the on-chip power dissipation must be lower that or equal to the maximum allowable power dissipation (PD(MAX)) dictated by Equation 3. where • TJ(MAX) is the target maximum junction temperature. • TA is the operating ambient temperature. • θJA is the package junction to ambient thermal resistance. (3) |
|
|
Link URL |
| Cho đến nay ALLDATASHEET có giúp ích cho doanh nghiệp của bạn hay không? [ DONATE ] |
Alldatasheet là | Quảng cáo | Liên lạc với chúng tôi | Chính sách bảo mật | Liên kết đến bảng dữ liệu | Trao đổi link | Tìm kiếm theo nhà sản xuất All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |