| công cụ tìm kiếm bảng dữ liệu linh kiện điện tử |
|
DP8572AMD/883 bảng dữ liệu(PDF) 10 Page - National Semiconductor (TI) |
|
|
|
|||||||||||||||||||||||||||||
DP8572AMD/883 bảng dữ liệu(HTML) 10 Page - National Semiconductor (TI) |
|
10 / 22 page ![]() Functional Description (Continued) The oscillator is programmed via the Real Time Mode Reg- ister to operate at various frequencies The crystal oscillator is designed to offer optimum performance at each frequen- cy Thus at 32768 kHz the oscillator is configured as a low frequency and low power oscillator At the higher frequen- cies the oscillator inverter is reconfigured In addition to the inverter the oscillator feedback bias resistor is included on chip as shown in Figure 4 The oscillator input may be driv- en from an external source if desired Refer to test mode application note for details The oscillator stability is en- hanced through the use of an on chip regulated power sup- ply The typical range of trimmer capacitor (as shown in Oscilla- tor Circuit Diagram Figure 4 and in the typical application) at the oscillator input pin is suggested only to allow accurate tuning of the oscillator This range is based on a typical printed circuit board layout and may have to be changed depending on the parasitic capacitance of the printed circuit board or fixture being used In all cases the load capaci- tance specified by the crystal manufacturer (nominal value 11 pF for the 32768 crystal) is what determines proper os- cillation This load capcitance is the series combination of capacitance on each side of the crystal (with respect to ground) TLF9980 – 9 FIGURE 4 Oscillator Circuit Diagram ROUT XTAL Co Ct (Switched Internally) 3232768 kHz 47 pF 2 pF – 22 pF 150 kX to 350 kX 4194304 MHz 68 pF 0 pF – 80 pF 500X to 900X 49152 MHz 68 pF 29 pF – 49 pF 500X to 900X INTERRUPT LOGIC FUNCTIONAL DESCRIPTION The RTC has the ability to coordinate processor timing ac- tivities To enhance this an interrupt structure has been im- plemented which enables several types of events to cause interrupts Interrupts are controlled via two Control Regis- ters in block 1 and two Status Registers in block 0 (See Register Description for notes on paging and also Figure 5 and Table I) The interrupts are enabled by writing a one to the appropri- ate bits in Interrupt Control Register 0 andor 1 TABLE I Registers that are Applicable to Interrupt Control Register Name Register Page Address Select Select Main Status Register X X 00H Periodic Flag Register 0 0 03H Interrupt Control 1 0 03H Register 0 Interrupt Control 1 0 04H Register 1 Output Mode 1 0 02H Register The Interrupt Status Flag D0 in the Main Status Register indicates the state of INTR and MFO outputs It is set when either output becomes active and is cleared when all RTC interrupts have been cleared and no further interrupts are pending (ie both INTR and MFO are returned to their inac- tive state) This flag enables the RTC to be rapidly polled by the mP to determine the source of an interrupt in a wired OR interrupt system (The Interrupt Status Flag provides a true reflection of all conditions routed to the external pins) Status for the interrupts are provided by the Main Status Register and the Periodic Flag Register Bits D1 – D5 of the Main Status Register are the main interrupt bits These register bits will be set when their associated timing events occur Enabled Alarm comparisons that occur will set its Main Status Register bit to a one However an exter- nal interrupt will only be generated if the Alarm interrupt enable bit is set (see Figure 5 ) Disabling the periodic interrupts will mask the Main Status Register periodic bit but not the Periodic Flag Register bits The Power Fail Interrupt bit is set when the interrupt is en- abled and a power fail event has occurred and is not reset until the power is restored If all interrupt enable bits are 0 no interrupt will be asserted However status still can be read from the Main Status Register in a polled fashion (see Figure 5 ) To clear a flag in bits D2 and D3 of the Main Status Register a 1 must be written back into the bit location that is to be cleared For the Periodic Flag Register reading the status will reset all the periodic flags 10 |
|
|
Link URL |
| Cho đến nay ALLDATASHEET có giúp ích cho doanh nghiệp của bạn hay không? [ DONATE ] |
Alldatasheet là | Quảng cáo | Liên lạc với chúng tôi | Chính sách bảo mật | Liên kết đến bảng dữ liệu | Trao đổi link | Tìm kiếm theo nhà sản xuất All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |