| công cụ tìm kiếm bảng dữ liệu linh kiện điện tử |
|
DRV10983ZPWPR bảng dữ liệu(PDF) 41 Page - Texas Instruments |
|
|
|
|||||||||||||||||||||||||||||
DRV10983ZPWPR bảng dữ liệu(HTML) 41 Page - Texas Instruments |
|
41 / 58 page ![]() 41 DRV10983 www.ti.com SLVSCP6C – JULY 2014 – REVISED MAY 2016 Product Folder Links: DRV10983 Submit Documentation Feedback Copyright © 2014–2016, Texas Instruments Incorporated Table 8. Default EEPROM Value Address Default Value 0x20 0x4A 0x21 0x4E 0x22 0x2A 0x23 0x00 0x24 0x98 0x25 0xE4 0x26 0x7A 0x27 0xFC 0x28 0x69 0x29 0xB7 0x2A 0xAD 0x2B 0x0C (1) R/W (2) Read only 9.5.3 Register Definition Table 9. Register Description Register Data Description Name Address Bits SpeedCtrl1(1) 0x00 7:0 SpdCtrl[7:0] 8 LSB of a 9-bit value used for the motor speed. If OverRide = 1, the user can directly control the motor speed by writing to the register through I2C. SpeedCtrl2(1) 0x01 7 OverRide Use to control the SpdCtrl [8:0] bits. If OverRide = 1, the user can write the speed command through I2C. 6:1 N/A N/A 0 SpdCtrl [8] MSB of a 9-bit value used for the motor speed. If OverRide = 1, user can directly control the motor speed by writing to the register through I2C. The MSB should be written first. Digital takes a snapshot of the MSB when LSB is written. DevCtrl(1) 0x02 7:0 enProgKey[7:0] 8-bit byte use to enable programming in the EEPROM. To program the EEPROM, enProgKey = ‘1011 0110’ (0xB6), followed immediately by eeWrite = 1. Otherwise, enProgKey value is reset. EECtrl(1) 0x03 7 sleepDis Set to 1 to disable entering into sleep or standby mode. 6 SIdata Set to 1 to enable the writing to the configuration registers. 5 eeRefresh Copy EEPROM data to register. 4 eeWrite Bit used to program (write) to the EEPROM. 3:0 N/A N/A Status(2) 0x10 7 OverTemp Bit to indicate device temperature is over its limits. 6 Slp_Stdby Bit to indicate that device went into sleep or standby mode. 5 OverCurr Bit to indicate that a phase to phase overcurrent event happened. This is a sticky bit, once written, it stays high even if overcurrent signal goes low. This bit is cleared on Read. 4 MtrLck Bit to indicate that the motor is locked. 3 N/A N/A 2 N/A N/A 1 N/A N/A 0 N/A N/A |
|
Link URL |
| Cho đến nay ALLDATASHEET có giúp ích cho doanh nghiệp của bạn hay không? [ DONATE ] |
Alldatasheet là | Quảng cáo | Liên lạc với chúng tôi | Chính sách bảo mật | Liên kết đến bảng dữ liệu | Trao đổi link | Tìm kiếm theo nhà sản xuất All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |