| công cụ tìm kiếm bảng dữ liệu linh kiện điện tử |
|
LM4990MM bảng dữ liệu(PDF) 6 Page - National Semiconductor (TI) |
|
|
|
|||||||||||||||||||||||||||||
LM4990MM bảng dữ liệu(HTML) 6 Page - National Semiconductor (TI) |
|
6 / 19 page ![]() Electrical Characteristics V DD = 2.6V (Notes 1, 2) The following specifications apply for the circuit shown in Figure 1, unless otherwise specified. Limits apply for T A = 25˚C. (Continued) Note 13: The Exposed-DAP of the LDA10B package should be electrically connected to GND or an electrically isolated copper area. the LM4990LD demo board has the Exposed-DAP connected to GND with a PCB area of 86.7mils x 585mils (2.02mm x 14.86mm) on the copper top layer and 550mils x 710mils (13.97mm x 18.03mm) on the copper bottom layer. Note 14: The thermal performance of the LLP and exposed-DAP TSSOP packages when used with the exposed-DAP connected to a thermal plane is sufficient for driving 4 Ω loads. The MSOP and ITL packages do not have the thermal performance necessary for driving 4Ω loads with a 5V supply and is not recommended for this application. Note 15: All bumps have the same thermal resistance and contribute equally when used to lower thermal resistance. All bumps must be connected to achieve specified thermal resistance. External Components Description See (Figure 1) Components Functional Description 1. R i Inverting input resistance which sets the closed-loop gain in conjunction with R f. This resistor also forms a high pass filter with C i at fC= 1/(2 π R iCi). 2. C i Input coupling capacitor which blocks the DC voltage at the amplifiers input terminals. Also creates a highpass filter with R i at fc = 1/(2 π R iCi). Refer to the section, Proper Selection of External Components, for an explanation of how to determine the value of C i. 3. R f Feedback resistance which sets the closed-loop gain in conjunction with R i. 4. C S Supply bypass capacitor which provides power supply filtering. Refer to the Power Supply Bypassing section for information concerning proper placement and selection of the supply bypass capacitor. 5. C B Bypass pin capacitor which provides half-supply filtering. Refer to the section, Proper Selection of External Components, for information concerning proper placement and selection of C B. Typical Performance Characteristics LD and MH Specific Characteristics THD+N+N vs Frequency V DD = 5V, RL =4 Ω, and P O =1W THD+N+N vs Output Power V DD = 5V, RL =4 Ω,andf=1kHz 20051030 20051031 www.national.com 6 |
|
|
Link URL |
| Cho đến nay ALLDATASHEET có giúp ích cho doanh nghiệp của bạn hay không? [ DONATE ] |
Alldatasheet là | Quảng cáo | Liên lạc với chúng tôi | Chính sách bảo mật | Liên kết đến bảng dữ liệu | Trao đổi link | Tìm kiếm theo nhà sản xuất All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |