PI5A3166 datasheet(3/9 Pages) PERICOM

3 / 9 page

|||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||

2015-09-0003

PT0444-1

09/23/15

PI5A3166

Low Voltage SPST 0.8Ω Analog Switch

DC Electrical Characteristics

(TA = –40°C to 85°C, unless otherwise noted.)

Parameter

Description

Test Conditions

Supply Voltage

Min

Typ

Max

Units

IAR

Analog Input Signal Range

VCC

ON Resistance

(1)

IA = 100mA, VB = 0V

4.5V

0.7

1.1



IA = 100mA, VB= 2.4V

0.6

1.0

IA = 100mA, VB = 4.5V

0.8

1.2

IA = 100mA, VB = 0V

3.0V

0.8

1.3

IA = 100mA, VB = 3.0V

0.9

1.9

IA = 100mA, VB = 0V

2.3V

1.0

1.5

IA = 100mA, VB = 2.3V

1.2

1.8

IA = 100mA, VB = 0V

1.65V

1.3

1.9

IA = 100mA, VB = 1.65V

2.0

2.8

ONF

ON Resistance Flatness

(2)

IA = 100mA, VB = 0V,2.4V,4.5V

4.5V

0.2

0.4



IA = 100mA, VB = 0V,1.5V,3.3V

3.3V

0.2

0.4

IA = 100mA, VB = 0V,1.1V,2.5V

2.5V

0.4

0.6

IA = 100mA, VB = 0V, 0.7V, 1.8V

1.8V

1.0

1.4

Input High Voltage

Logic High Level

VCC = 1.65V

VCC = 2.3V

1.2

VCC = 3V

1.3

VCC = 4.2V

1.5

VCC = 5.5V

1.8

Input Low Voltage

Logic Low Level

VCC = 1.65V

0.4

VCC = 2.3V

0.6

VCC = 3V

0.8

VCC = 4.2V

VCC = 5.5V

1.2

IOFF (B)

Source Off Leakage

Current

VCC=5.5V, VA =1V, 4.5V

VB =1V, 4.5V

VCC = 3V

-20

+20

INC(A, B)

Channel On Leakage

Current

VCC = 1.65 to

5.5V

-40

+40

IPWROFF

Input Leakage Current for

Power off

0≤V

A≤5.5V

0≤V

B≤5.5V

VCC =0V

-5

µA

Quiescent Supply Current

All channels ON or OFF,

VB = VCC or GND, IOUT=0

VCC = 3.6V

0.002

0.1

µA

VCC = 5.5V

0.002

0.1

Notes:

1. Measured by voltage drop between A and B pins at the indicated current through the device. ON resistance is determined by the lower

of the voltages on two ports (A or B).

2. Flatness is defined as difference between maximum and minimum value of ON resistance over the specified range of conditions.

Guaranteed by design.

Capacitance

(1)

Symbol

Parameter

Test Conditions

Min.

Typ.

Max.

Units

CIN

Control Input

VCC = 5.0V, f =1 MHz, TA=25°C

3.5

CIO-B

For B Port, Switch OFF

15.0

CIOA-ON

For A Port, Switch ON

34.0

Notes:

1. Capacitance is characterized but not tested in production

PI5A3166 bảng dữ liệu(PDF) 3 Page - Pericom Semiconductor Corporation

PI5A3166 bảng dữ liệu(HTML) 3 Page - Pericom Semiconductor Corporation

Html Pages

1 2 3 4 5 6 7 8 9

bảng dữ liệu tải về

Link URL