| công cụ tìm kiếm bảng dữ liệu linh kiện điện tử |
|
SP5301 bảng dữ liệu(PDF) 7 Page - Sipex Corporation |
|
|
|||||||||||||||||||||||||||||
SP5301 bảng dữ liệu(HTML) 7 Page - Sipex Corporation |
|
7 / 13 page ![]() 7 SP5301DS/10 SP5301 Universal Serial Bus Transceiver © Copyright 2000 Sipex Corporation PIN ASSIGNMENTS Pin 1 — RERR — Receive Error. This CMOS level output pin is forced HIGH when both D+ and D- are HIGH to signal an error state. CAUTION: Since RERR is a CMOS output, care must be taken to ensure that RERR is NOT connected to V CC or GND. Pin 2 — OE — Output Enable Not. When asserted LOW, this input pin enables the driver to transmit data on the bus. When HIGH, the receiver is active and the driver outputs are in tri-state. Pin 3 — RCV — Receive data. This is a CMOS level output pin from D+ and D-, typically connected to the inputs of the USB Serial Interface Engine (SIE). Pin 4, 5 — VP, VM — Gated version of D+ and D-. Used to detect single ended zero (SEO), error conditions, and interconnect speed. These pins have CMOS level outputs. O P VO M VT L U S E R 00 0 E S 01 w o L c i g o L 10 h g i H c i g o L 11 d e n i f e d n U P VM VT L U S E R 00 0 E S 01 d e e p S w o L 10 d e e p S l l u F 11 r o r r E VCC GND 1 2 3 4 11 12 13 14 5 6 7 10 9 8 RERR OE RCV VP VM SUSPND SPEED RSEO D- D+ VPO VMO Pin 6 — SUSPND — Suspend. This input pin provides a low power state for the SP5301 while the USB bus is inactive. While the SUSPND pin is asserted HIGH, it will drive RCV pin LOW. Pin 7 — GND — Ground. Pin 8 — RSEO — Receive Single Ended Zero. This CMOS level output pin is forced HIGH when both D+ and D- are LOW to signal the end of packet (EOP) in signal transmission. CAUTION: Since RSEO is a CMOS output, care must be taken to ensure that RSEO is NOT connected to V CC or GND. Pin 9 — SPEED — Speed. Edge rate control. This input pin determines edge rates, where a logic HIGH designates edge rates for "full speed" and logic LOW designates edge rates for "low speed." Pin 10, 11 — D-, D+ — Data-, Data+. These differential data bus I/O pins conform to the Universal Serial Bus standard. Pin 12, 13 — VPO, VMO — These are the PINOUT logic inputs to the differential driver, typically connected to the outputs of the Serial Interface Engine (SIE). Pin 14 — V CC — +3.0V to +3.6V power supply. |
|
|
Link URL |
| Cho đến nay ALLDATASHEET có giúp ích cho doanh nghiệp của bạn hay không? [ DONATE ] |
Alldatasheet là | Quảng cáo | Liên lạc với chúng tôi | Chính sách bảo mật | Liên kết đến bảng dữ liệu | Trao đổi link | Tìm kiếm theo nhà sản xuất All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |