SP514CF datasheet(2/20 Pages) SIPEX

2 / 20 page

Rev. 3/05/04

SP514 Multi–Mode Serial Transceiver

SPECIFICATIONS

A = +25°C and VCC = +4.75V to +5.25V unless otherwise noted.

MIN.

TYP.

MAX.

UNITS

CONDITIONS

LOGIC INPUTS

0.8

Volts

2.0

Volts

LOGIC OUTPUTS

0.4

Volts

OUT= –3.2mA

2.4

Volts

OUT= 1.0mA

V.28 DRIVER

DC Parameters

Outputs

Open Circuit Voltage

+15

Volts

per Figure 1

Loaded Voltage

+5.0

+15

Volts

per Figure 2

Short-Circuit Current

+100

per Figure 4

Power-Off Impedance

300

Ω

per Figure 5

AC Parameters

CC = +5V & TA = +25°C for AC parameters

Outputs

Transition Time

1.5

µs

per Figure 6; +3V to -3V

Instantaneous Slew Rate

V/µs

per Figure 3

Propagation Delay

PHL

0.5

µs

PLH

0.5

µs

Max.Transmission Rate

120

230

kbps

V.28 RECEIVER

DC Parameters

Inputs

Input Impedance

kΩ

per Figure 7

Open-Circuit Bias

+2.0

Volts

per Figure 8

HIGH Threshold

1.7

3.0

Volts

LOW Threshold

0.8

1.2

Volts

AC Parameters

CC = +5V & TA = +25°C for AC parameters

Propagation Delay

PHL

100

500

PLH

100

500

ABSOLUTE MAXIMUM RATINGS

These are stress ratings only and functional operation

of the device at these ratings or any other above those

indicated in the operation sections of the specifications

below is not implied. Exposure to absolute maximum

rating conditions for extended periods of time may

affect reliability.

CC............................................................................+7V

Input Voltages:

Logic...............................-0.3V to (V

CC+0.5V)

Drivers............................-0.3V to (V

CC+0.5V)

Receivers........................................±15.5V

Output Voltages:

Logic................................-0.3V to (V

CC+0.5V)

Drivers................................................±15V

Receivers........................-0.3V to (V

CC+0.5V)

Storage Temperature..........................-65˚C to +150˚C

Power Dissipation.........................................2000mW

Package Derating:

JA....................................................46 °C/W

JC...................................................16 °C/W

STORAGE CONSIDERATIONS

Due to the relatively large package size of the 80-pin

quad flat-pack, storage in a low humidity environment

is preferred. Large high density plastic packages are

moisture sensitive and should be stored in Dry Vapor

Barrier Bags. Prior to usage, the parts should remain

bagged and stored below 40°C and 60%RH. If the

parts are removed from the bag, they should be used

within 48 hours or stored in an environment at or below

20%RH. If the above conditions cannot be followed,

the parts should be baked for four hours at 125°C in

order remove moisture prior to soldering. Sipex ships

the 80-pin QFP in Dry Vapor Barrier Bags with a

humidity indicator card and desiccant pack.The

humidity indicator should be below 30%RH.

SP514CF bảng dữ liệu(PDF) 2 Page - Sipex Corporation

SP514CF bảng dữ liệu(HTML) 2 Page - Sipex Corporation

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20

bảng dữ liệu tải về

Link URL