| công cụ tìm kiếm bảng dữ liệu linh kiện điện tử |
|
TLE6288 bảng dữ liệu(PDF) 17 Page - Infineon Technologies AG |
|
|
|||||||||||||||||||||||||||||
TLE6288 bảng dữ liệu(HTML) 17 Page - Infineon Technologies AG |
|
17 / 23 page ![]() Preliminary Datasheet TLE6288 R Vp2 Page 17 13.01.2003 8.4 SPI Commands Command Table No Command MSB 14 13 12 11 10 9 8 7 6 5 4 3 2 1 LSB 1 Config. Regulator 1 1 0 0 1 Mode Ipk tfo Ihd tp X 2 Config. Regulator 2 1 0 1 0 Mode Ipk tfo Ihd tp X 3 Config. Regulator 3 1 0 1 1 Mode Ipk tfo Ihd tp X Ch. 6 Ch. 5 Ch 4 all all DIAG 6 4 Config. Ch1 - Ch6 1 1 0 0 H/L OL+ SB H/L OL+ SB H/L OL+ SB OR/ AND R/L D/F X X X 5 Set all to Default 1 0 0 0 X X X X X X X X X X X X 6 Diagnosis only 1 1 1 1 X X X X X X X X X X X X 7 Channels on / off 1 1 0 1 Ch6 Ch5 Ch4 Ch3 Ch2 Ch1 X X X X X X Legend of SPI Command Table: Mode: Operation mode of the current regulator: a) no regulation b) hold only c) peak&hold with minimum peak time d) peak&hold with programmed peak time Ipk : Peak current values 1.2A - 3.6A Ihd : Hold current values 0.7A - 2A tp : Peak time value 0.8ms – 3.6ms tfo : Fixed off time value 100µs – 400µs H/L : Channel 1-3 in highside or lowside configuration OL+SB : open load detection and switch bypassed detection activated or deactivated OR / AND : Boolean Operation (parallel input and corresponding SPI Bit) R/L : Autorestart or Latching overtemperature behaviour D/F : DIAG6/Overtemp pin set as Diagnosis output of channel 6 or as Overtemperature Flag Ch1-Ch6 : On / Off information of the output drivers (high active) Command description: Config. Regulator 1-3: With this command the values for for the current regulation and the functional mode of the channel is written into the internal logic registers. Config. Ch1- Ch6 : This command writes the configuration data of the three configurable channels (4- 6) and sets the Boolean operation and overtemperature behavior of all channels. It also and sets the DIAG6/Overtemp. pin to Diagnosis of channel 6 or Overtemperature Flag. Set all to default : This command sets all internal logic registers back to default settings. Diagnosis only : When this command is sent the 12 data bits are ignored. The internal logic registers are not changed. Channels on/off : With this command the SPI bits for the ON/OFF information of the 6 Channels are set Note: Specified control words (valid commands) are executed and the diagnosis register is reset after the rising CS edge. Not specified control words are not executed (cause no function) and the diagnosis register is not reset after the CS = L H signal. |
|
|
Link URL |
| Cho đến nay ALLDATASHEET có giúp ích cho doanh nghiệp của bạn hay không? [ DONATE ] |
Alldatasheet là | Quảng cáo | Liên lạc với chúng tôi | Chính sách bảo mật | Liên kết đến bảng dữ liệu | Trao đổi link | Tìm kiếm theo nhà sản xuất All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |