| công cụ tìm kiếm bảng dữ liệu linh kiện điện tử |
|
INA333-HT bảng dữ liệu(PDF) 14 Page - Texas Instruments |
|
|
|
|||||||||||||||||||||||||||||
INA333-HT bảng dữ liệu(HTML) 14 Page - Texas Instruments |
|
14 / 26 page ![]() INA333-HT SBOS514C – MARCH 2010 – REVISED OCTOBER 2013 www.ti.com APPLICATION INFORMATION Application information below is provided for SETTING THE GAIN commercial temperature as a reference and not for high temperature. Gain of the INA333 is set by a single external resistor, RG, connected between pins 1 and 8. The It is not recommended to use a gain < 100 for high value of RG is selected according to Equation 1: temperature (210°C) applications. For gains > 100 in such applications, a compensation circuit is needed G = 1 + (100 k Ω/RG) (1) (1) at pins 1 and 8. The circuit is needed at each pin and Table 2 lists several commonly-used gains and consists of a resistor in series with a capacitor resistor values. The 100 k Ω term in Equation 1 referenced to ground. Recommended values for the comes from the sum of the two internal feedback resistor and capacitor are 3.5 k Ω and 10 nF resistors of A1 and A2. These on-chip resistors are respectively. laser trimmed to accurate absolute values. The Figure 34 shows the basic connections required for accuracy and temperature coefficient of these operation of the INA333. Good layout practice resistors are included in the gain accuracy and drift mandates the use of bypass capacitors placed close specifications of the INA333. to the device pins as shown. The stability and temperature drift of the external gain The output of the INA333 is referred to the output setting resistor, RG, also affects gain. The contribution reference (REF) terminal, which is normally of RG to gain accuracy and drift can be directly grounded. This connection must be low-impedance to inferred from the gain Equation 1. Low resistor values assure good common-mode rejection. Although 15 Ω required for high gain can make wiring resistance or less of stray resistance can be tolerated while important. Sockets add to the wiring resistance and maintaining specified CMRR, small stray resistances contribute additional gain error (possibly an unstable of tens of ohms in series with the REF pin can cause gain error) in gains of approximately 100 or greater. noticeable degradation in CMRR. To ensure stability, avoid parasitic capacitance of more than a few picofarads at the RG connections. Careful matching of any parasitics on both RG pins maintains optimal CMRR over frequency. 14 Submit Documentation Feedback Copyright © 2010–2013, Texas Instruments Incorporated Product Folder Links: INA333-HT |
|
|
Link URL |
| Cho đến nay ALLDATASHEET có giúp ích cho doanh nghiệp của bạn hay không? [ DONATE ] |
Alldatasheet là | Quảng cáo | Liên lạc với chúng tôi | Chính sách bảo mật | Liên kết đến bảng dữ liệu | Trao đổi link | Tìm kiếm theo nhà sản xuất All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |