H7CX-R11WD1-N datasheet(19/56 Pages) OMRON

19 / 56 page

H7CX-A

@-N

Counter

Absolute Value Setting/Forecast Value Setting (

setm)

For the 2 count output mode, an absolute value setting (

abs) or

forecast value setting (

ofst) can be set for set value 1.

When a forecast value is set, specify the forecast value set value (i.e.,

the deviation for the set value).

The forecast output (output 1) turns ON when the present value

reaches the forecast value.

If the forecast set value is greater than or equal to the set value, the

forecast output (output 1) will turn ON as soon as counting starts.

If the forecast value setting is used, specify the set value 2 minus the

forecast value setting for set value 1.

Set Value Upper Limit (

sl-h)

Set the upper limit for the set value when it is set in run mode.

The setting can be made from 1 to 9999 for 4-digit models and from

1 to 999999 for 6-digit models.

Forecast Set Upper Limit (

pl-h)

Set the upper limit for the forecast set value.

The setting can be made from 1 to 9999 for 4-digit models and from

1 to 999999 for 6-digit models.

Batch Count Upper Limit (

bl-h)

Set the upper limit for the batch count value. The setting can be made

from 1 to 9999 for 4-digit models and from 1 to 999999 for 6-digit

models.

Output Allocation (

otst)

When using an H7CX-AU

@-N model as a 2-stage counter, the output

can be flexibly allocated to either stage 1 or 2.

The transistor output can be allocated to SV1 and the contact output

to SV2 or vice verse, as in the following tables.

H7CX-AU-N/-AUD1-N

H7CX-AUSD1-N

Key Protect Level (

kypt)

Set the key protect level.

Refer to Key Protect Level on page page 36.

Output ON Count Alarm Set Value (

on-a)

Set the alarm value for the output ON count.

The limit can be set to between 0

× 1000 (0 times) and 9999 × 1000

(9,999,000 times). Only the underlined values are set. The alarm will

be disabled if 0 is set.

If the total ON count of the output exceeds the alarm set value,

will be displayed on the Timer to indicate that the output ON count

alarm value was exceeded. Refer to Self-diagnostic Function on page

page 36 for information on the

e3 display.

ON Count Alarm Set Values for Outputs 1 and 2 (OUT1

and OUT2) (

on1a and on2a)

Set the ON count alarm values for the outputs 1 and 2.

The limit can be set to between 0

× 1000 (0 times) and 9999 × 1000

(9,999,000 times). Only the underlined values are set. The alarm will

be disabled if 0 is set.

If the total ON count of instantaneous output 1 or 2 exceeds the alarm

set value,

e3 will be displayed on the Timer to indicate that the output

ON count alarm value was exceeded. Refer to Self-diagnostic

Function on page page 36 for information on the

e3 display.

Output ON Count Monitor Value (

on-c)

The monitor value is only displayed. It cannot be set.

The output ON count will be 1,000 times the displayed value.

ON Count Monitor Values for Outputs 1 and 2 (OUT1 and

OUT2) (

on1c and on2c)

The monitor value for output 1 or 2 is only displayed. It cannot be set.

The output ON count will be 1,000 times the displayed value.

Output 1

Output 2

off

Transistor (12-13)

Contact (3, 4, 5)

Transistor (12-13)

Output 1

Output 2

off

Transistor (12-13)

Transistor with diode (3, 4, 5)

Transistor (12-13)

Set value 2

Set value 1

Control output 1 (OUT1)

Control output 2 (OUT2)

Count value

Example: F Mode

Set value

Forecast

value

Forecast set value

Forecast output (OUT1)

Control output (OUT 2)

Count value

Example: F Mode

H7CX-R11WD1-N bảng dữ liệu(PDF) 19 Page - Omron Electronics LLC

H7CX-R11WD1-N bảng dữ liệu(HTML) 19 Page - Omron Electronics LLC

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56

bảng dữ liệu tải về

Link URL