H7CX-R11D1-N datasheet(44/56 Pages) OMRON

44 / 56 page

H7CX-R

@-N

(99.9 s)

(0.0 s)

(Enabled)

(Disabled)

(99999)

(0)

(19.99 s)

(0.00 s)

(999999)

(1)

(999.9 s)

(0.1 s)

kp-1

off

99999

0.00

19.99

999999

kp-2

kp-3

kp-4

kp-5

kp-6

kp-7

9999

Procedure for Models Other than “-R11W

@” Models

Procedure for “-R11W

@” Models

(9999

× 1000 times)

(KP-1)

(KP-2)

(KP-3)

(KP-4)

(KP-5)

(KP-6)

(KP-7)

Note: Not displayed in AMD-compatible mode.

*1 Set each digit using the individual

U Key.

Note: The monitor value is only

displayed. It cannot be set.

Output OFF

delay

(OFFD)

Output ON

count alarm set

value/monitor

value

• Set each digit using the individual

U Key.

Auto-zero

time

(AUTO0)

Startup

time

(STMR)

Peak/bottom

hold

enabled

(DHLD)

Output

hysteresis

(HYS)

Set value

upper limit

(SL-H)

Key

protect

level

(KYPT)

• Set each digit using the individual

U Key.

• Enable or disable peak/bottom hold using the

U Key.

• Set the output hysteresis using the

U Key.

• Set each digit using the individual

U Key.

Note: The measurement value after prescaling is set.

• Set each digit using the individual

U Key.

• Set the key protect level using the

U Key.

Output

ON count

alarm set

value

Output

ON count

monitor

value

Output 1

(OUT1) ON

count alarm

set value

Output 2

(OUT2) ON

count alarm

set value

Note: The monitor value is only

displayed. It cannot be set.

Note: The monitor value is only

displayed. It cannot be set.

Output 1

(OUT1) ON

count

monitor

value

Output 2

(OUT2) ON

count

monitor

value

(9999

× 1000 times)

(9999

× 1000 times)

(MV)

(SMP)

(99.999)

(1.000)

(0.001)

The characters displayed in reverse video are the default settings.

smp

Power ON

Run mode

Step2

Change to Function Setting Mode.

3 s min.*2

3 s min.*1

• Set the decimal point position using the

U Key.

*1 If the mode is switched to the function setting mode during operation, operation will

continue.

*2 Changes made to settings in function setting mode are enabled for the first time when the

mode is changed to run mode.

Also, when settings are changed, the counter is reset (measured values initialized and

output turned OFF) on returning to run mode.

Function

setting mode

Averaging

method

(AUGT)

Prescale value

(PSCL)

Decimal point

position

(DP)

(No decimal point) (One digit after

decimal point)

(Two digits after

decimal point)

(Three digits after

decimal point)

• Set each digit using the individual

U Key.

• Set the averaging method using the

U Key.

Note: Not displayed in AMD-compatible mode.

For details on operations in run mode, refer to page page 47.

H7CX-R11D1-N bảng dữ liệu(PDF) 44 Page - Omron Electronics LLC

H7CX-R11D1-N bảng dữ liệu(HTML) 44 Page - Omron Electronics LLC

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56

bảng dữ liệu tải về

Link URL