ATmega16 datasheet(220/315 Pages) ATMEL

220 / 315 page

220

ATmega16(L)

2466E–AVR–10/02

•

2 single Program Memory Break Points + 1 Program Memory Break Point with mask

(“range Break Point”)

•

2 single Program Memory Break Points + 1 Data Memory Break Point with mask

(“range Break Point”)

A debugger, like the AVR Studio, may however use one or more of these resources for

its internal purpose, leaving less flexibility to the end-user.

A list of the On-chip Debug specific JTAG instructions is given in “On-chip Debug Spe-

cific JTAG Instructions” on page 220.

The JTAGEN Fuse must be programmed to enable the JTAG Test Access Port. In addi-

tion, the OCDEN Fuse must be programmed and no Lock bits must be set for the On-

chip Debug system to work. As a security feature, the On-chip Debug system is disabled

when any Lock bits are set. Otherwise, the On-chip Debug system would have provided

a back-door into a secured device.

The AVR JTAG ICE from Atmel is a powerful development tool for On-chip Debugging

of all AVR 8-bit RISC Microcontrollers with IEEE 1149.1 compliant JTAG interface. The

JTAG ICE and the AVR Studio user interface give the user complete control of the inter-

nal resources of the microcontroller, helping to reduce development time by making

debugging easier. The JTAG ICE performs real-time emulation of the micrcontroller

while it is running in a target system.

Please refer to the Support Tools section on the AVR pages on www.atmel.com for a full

description of the AVR JTEG ICE. AVR Studio can be downloaded free from Software

section on the same web site.

All necessary execution commands are available in AVR Studio, both on source level

and on disassembly level. The user can execute the program, single step through the

code either by tracing into or stepping over functions, step out of functions, place the

cursor on a statement and execute until the statement is reached, stop the execution,

and reset the execution target. In addition, the user can have an unlimited number of

code breakpoints (using the BREAK instruction) and up to two data memory break-

points, alternatively combined as a mask (range) Break Point.

On-chip Debug Specific

JTAG Instructions

The On-chip Debug support is considered being private JTAG instructions, and distrib-

uted within ATMEL and to selected third party vendors only. Instruction opcodes are

listed for reference.

PRIVATE0; $8

Private JTAG instruction for accessing On-chip Debug system.

PRIVATE1; $9

Private JTAG instruction for accessing On-chip Debug system.

PRIVATE2; $A

Private JTAG instruction for accessing On-chip Debug system.

PRIVATE3; $B

Private JTAG instruction for accessing On-chip Debug system.

ATMEGA16 bảng dữ liệu(PDF) 220 Page - ATMEL Corporation

ATMEGA16 bảng dữ liệu(HTML) 220 Page - ATMEL Corporation

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

bảng dữ liệu tải về

Link URL