LM99_15 datasheet(6/30 Pages) TI

6 / 30 page

VIH

VIL

SMBCLK

VIH

VIL

SMBDAT

tBUF

tHD;STA

tLOW

tHD;DAT

tHIGH

tSU;DAT

tSU;STA

tSU;STO

LM99

SNIS129D – JANUARY 2003 – REVISED MARCH 2013

www.ti.com

SMBus Digital Switching Characteristics

Unless otherwise noted, these specifications apply for VDD = +3.0 Vdc to +3.6 Vdc, CL (load capacitance) on output lines = 80

pF. Boldface limits apply for TA = TJ = TMIN to TMAX; all other limits TA = TJ = +25°C, unless otherwise noted.

The switching characteristics of the LM99 fully meet or exceed the published specifications of the SMBus version 2.0. The

following parameters are the timing relationships between SMBCLK and SMBData signals related to the LM99. They adhere

to but are not necessarily the SMBus bus specifications.

Typical(1)

Limits(2)

Units

Symbol

Parameter

Conditions

(Limit)

fSMB

SMBus Clock Frequency

100

kHz (max)

kHz (min)

tLOW

SMBus Clock Low Time

from VIN(0)max to VIN(0)max

4.7

µs (min)

ms (max)

tHIGH

SMBus Clock High Time

from VIN(1)min to VIN(1)min

4.0

µs (min)

tR,SMB

SMBus Rise Time

See(3)

µs (max)

tF,SMB

SMBus Fall Time

See(4)

0.3

µs (max)

tOF

Output Fall Time

CL = 400 pF,

250

ns (max)

IO = 3 mA

(4)

tTIMEOUT

SMBData and SMBCLK Time Low for Reset of

ms (min)

Serial Interface(5)

ms (max)

tSU;DAT

Data In Setup Time to SMBCLK High

250

ns (min)

tHD;DAT

Data Out Stable after SMBCLK Low

300

ns (min)

900

ns (max)

tHD;STA

Start Condition SMBData Low to SMBCLK Low

100

ns (min)

(Start condition hold before the first clock falling

edge)

tSU;STO

Stop Condition SMBCLK High to SMBData Low

100

ns (min)

(Stop Condition Setup)

tSU;STA

SMBus Repeated Start-Condition Setup Time,

0.6

µs (min)

SMBCLK High to SMBData Low

tBUF

SMBus Free Time Between Stop and Start

1.3

µs (min)

Conditions

(1)

Typicals are at TA = 25°C and represent most likely parametric normal.

(2)

Limits are ensured to AOQL (Average Outgoing Quality Level).

(3)

The output rise time is measured from (VIN(0)max + 0.15 V) to (VIN(1)min − 0.15 V).

(4)

The output fall time is measured from (VIN(1)min - 0.15 V) to (VIN(1)min + 0.15 V).

(5)

Holding the SMBData and/or SMBCLK lines Low for a time interval greater than tTIMEOUT will reset the LM99's SMBus state machine,

therefore setting SMBData and SMBCLK pins to a high impedance state.

Figure 2. SMBus Communication

Submit Documentation Feedback

Product Folder Links: LM99

LM99 bảng dữ liệu(PDF) 6 Page - Texas Instruments

LM99 bảng dữ liệu(HTML) 6 Page - Texas Instruments

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30

bảng dữ liệu tải về

Link URL