| công cụ tìm kiếm bảng dữ liệu linh kiện điện tử |
|
MAX2003C/D bảng dữ liệu(PDF) 10 Page - Maxim Integrated Products |
|
|
|||||||||||||||||||||||||||||
MAX2003C/D bảng dữ liệu(HTML) 10 Page - Maxim Integrated Products |
|
10 / 20 page ![]() operation, the SNS voltage ramps between 0.044VCC and 0.050VCC, which is 220mV and 250mV when VCC is 5V (Figure 7). The average voltage at SNS, therefore, is 235mV, and can be used to calculate the charge cur- rent as follows: ICHARGE = 0.235V / RSNS where RSNS is the sense resistor and ICHARGE is the charge current required. Circuits without SNS Resistor In some applications (shown later), SNS is tied directly to ground. In these cases, the MOD pin remains on until any one charge-termination condition is exceeded (Figure 8). A reasonable external current limit (such as a current-limited DC source) must be provided for these applications, to prevent battery damage due to excessive charge currents. Charge Termination The MAX2003 has several charge-termination methods. The termination method selected depends on the type of battery and charge rate used. Table 1 summarizes the conditions used to terminate fast-charge with differ- ent battery types and charge rates. Temperature Rate Termination The Temperature Rate Termination ( ∆T/∆t) method ter- minates fast-charge when a particular rate-of-change in temperature is exceeded. As the battery begins fast- charge, its temperature increases at a slow rate. When the battery nears full capacity, this rate of temperature change increases. When the rate of temperature change exceeds a preset number, fast-charge is termi- nated. This method of fast-charge termination can be used for both NiCd and NiMH batteries. The MAX2003 samples the voltage at the TS pin every 34 seconds and compares it with a value taken 68 seconds earlier. Since an NTC thermistor is used for temperature measurements, a gradual rise in temperature will result in successively lower voltage readings. If the new reading is more than 0.0032VCC (16mV for VCC = 5V) below the old reading, fast-charge is terminated. The MAX2003A varies the sampling interval as a function of charge rate (Table 4). As the charge rate increases, the sampling interval decreases, thereby allowing more accurate termination of fast charge. Note: This method of charge termination is valid only when the battery’s temperature is between VLTF and VTCO (Figure 5). NiCd/NiMH Battery Fast-Charge Controllers 10 ______________________________________________________________________________________ TIME TIME TIME 0 0 0 MOD SNS ILOAD 0.044 VCC 0.050 VCC VCC IBAT FAST CHARGE FAST-CHARGE TERMINATE Figure 7. Current Regulation with an SNS Resistor TIME TIME SNS = 0V TIME 0 0 MOD SNS ILOAD 0.044 VCC 0.050 VCC VCC IBAT FAST CHARGE FAST-CHARGE TERMINATE Figure 8. Current Regulation without an SNS Resistor |
|
|
Link URL |
| Cho đến nay ALLDATASHEET có giúp ích cho doanh nghiệp của bạn hay không? [ DONATE ] |
Alldatasheet là | Quảng cáo | Liên lạc với chúng tôi | Chính sách bảo mật | Liên kết đến bảng dữ liệu | Trao đổi link | Tìm kiếm theo nhà sản xuất All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |