công cụ tìm kiếm bảng dữ liệu linh kiện điện tử
  Vietnamese  ▼
ALLDATASHEET.VN

X  

LX8610-33CDM bảng dữ liệu(PDF) 3 Page - Microsemi Corporation

tên linh kiện LX8610-33CDM
Giải thích chi tiết về linh kiện  1A BiCMOS Very Low Dropout Regulators
PDF  6 Pages
Scroll/Zoom Zoom In 100%  Zoom Out
nhà sản xuất  MICROSEMI [Microsemi Corporation]
Trang chủ  http://www.microsemi.com
Logo MICROSEMI - Microsemi Corporation

LX8610-33CDM bảng dữ liệu(HTML) 3 Page - Microsemi Corporation

  LX8610-33CDM Datasheet HTML 1Page - Microsemi Corporation LX8610-33CDM Datasheet HTML 2Page - Microsemi Corporation LX8610-33CDM Datasheet HTML 3Page - Microsemi Corporation LX8610-33CDM Datasheet HTML 4Page - Microsemi Corporation LX8610-33CDM Datasheet HTML 5Page - Microsemi Corporation LX8610-33CDM Datasheet HTML 6Page - Microsemi Corporation  
Zoom Inzoom in Zoom Outzoom out
 3 / 6 page
background image
Microsemi
Linfinity Microelectronics Division
11861 Western Avenue, Garden Grove, CA. 92841, 714-898-8121, Fax: 714-893-2570
Page 3
Copyright
© 2000
Rev. 0.6f,2000-09-15
LX8610-xx
1A BiCMOS Very Low Dropout Regulators
PRELIMINARY DATASHEET
A
M I CROSEM I
COM P A N Y

  
   

 
  
VIN
Positive supply input for the regulator. Bypass to GND with at least 2.2µF of low ESR, ESL capacitance if
supply source is further than 1 inch from the device.
VOUT
Output for the regulator. It is recommended to bypass to GND with at least 10µF although this is not required
for regulation, rather it is needed for transient response. Size your output capacitor to meet the transient
loading requirement. If you have a very dynamic load, a larger capacitor will improve the response to these
load steps.
GND
Reference ground. The input and output bypass capacitors should be connected to this pin. In addition the tab
on the SOT-223 package and pins 2,3,6, and 7 on the SOIC package are also used for heat sinking the device.
ADJ
Feedback pin for the regulator. For the LX8610-00, the output voltage can be set by two external resistors with
the following relationship: VOUT = 1.25V * (1 + RA / RB) where RA is the resistor connected between VOUT and
ADJ, and RB is the resistor connected between ADJ and GND.
ENALBE
Enable input. This pin has a threshold of about VIN / 2, it should be actively pulled high to enable the regulator.
This can be accomplished with a resistive pull-up. When low, it turns off the regulator and puts the device in a
low current shutdown state.
 
 
V
IN
LX8610-00
IN
ENABLE
GND
ADJ
OUT
V
OUT
V
REF
C
IN
C
OUT
R
A
R
B
1
8
2,3
6,7
4
5
+
=
B
A
R
R
V
V
REF
OUT
1
Figure 1 – Typical Application



Html Pages

1 2 3 4 5 6


bảng dữ liệu tải về

Go To PDF Page


Link URL



Cho đến nay ALLDATASHEET có giúp ích cho doanh nghiệp của bạn hay không?  [ DONATE ] 

Alldatasheet là   |   Quảng cáo   |   Liên lạc với chúng tôi   |   Chính sách bảo mật   |   Liên kết đến bảng dữ liệu    |   Trao đổi link   |   Tìm kiếm theo nhà sản xuất
All Rights Reserved©Alldatasheet.com


Mirror Sites
English : Alldatasheet.com  |   English : Alldatasheet.net  |   Chinese : Alldatasheetcn.com  |   German : Alldatasheetde.com  |   Japanese : Alldatasheet.jp
Russian : Alldatasheetru.com  |   Korean : Alldatasheet.co.kr  |   Spanish : Alldatasheet.es  |   French : Alldatasheet.fr  |   Italian : Alldatasheetit.com
Portuguese : Alldatasheetpt.com  |   Polish : Alldatasheet.pl  |   Vietnamese : Alldatasheet.vn
Indian : Alldatasheet.in  |   Mexican : Alldatasheet.com.mx  |   British : Alldatasheet.co.uk  |   New Zealand : Alldatasheet.co.nz
Family Site : ic2ic.com  |   icmetro.com