| công cụ tìm kiếm bảng dữ liệu linh kiện điện tử |
|
LX1562IDM bảng dữ liệu(PDF) 21 Page - Microsemi Corporation |
|
|
|||||||||||||||||||||||||||||
LX1562IDM bảng dữ liệu(HTML) 21 Page - Microsemi Corporation |
|
21 / 25 page ![]() SECOND-GENERATION POWER FACTOR C ONTROLLER LX1562/1563 PRODUCT DA T ABOOK 1996/1997 21 Copyright © 1996 Rev. 1.3 12/96 P RODUCTION D ATA S HEET APPLICATION INFORMA TION POWER MOSFET SELECTION The voltage rating of MOSFET and rectifier must be higher than the maximum value of the output voltage. V DS ≥ 1.2 VO MAX V DS ≥ 282V The RMS current can be approximated by multiplying the RMS current at the peak of the line by 0.7. I RMS = 0.7 ILP √D/3 D ≡ On-time duty cycle D = 0.39 at V AC = 100V I LP = 2.4A I RMS = (0.7)(2.4)( √.39/3) = 0.61A R DS ≤ P DC ≡ allowable power I RMS/triangle = ILP √D/3 dissipation. R DS ≤ = 1.6 Ω IRF730 with R DS = 1Ω Ω Ω Ω Ω and V DS = 400V meets the above requirements. P DC I RMS 2 1 0.61 I LP D INPUT RECTIFIER AND CAPACITOR SELECTION The current through each diode is a half-wave rectified sine wave. The maximum current happens at minimum line with a peak value of 1.2A. I AVE = = = 0.38A choose 1N4004 with 1A rating. P DISS = (IAVE) (VF) = 0.38 x 0.9 = 0.344W T J = TA + PD x θJA assuming θ JA = 65°C/W for 1/8" lead length. T J = 80 + (.344)(65) = 102°C I PEAK π 1.2 π Assuming ϕ is the percentage of allowable input current ripple, C1 can be calculated using the following equations: R EFF = C1 ≥ f SW ≡ Switching frequency of inductor current at peak input voltage. if ϕ = 3% R EFF = = 117 Ω C1 ≥ = 0.9µF choose 1µF, 250V capacitor. 2 P O η I P 2 1 ϕ 2π R EFF fSW 2 x 80 (.95)(1.2)2 1 (.03)(2 π)(117)(50000) OUTPUT CAPACITOR SELECTION There are mainly two criteria for selecting the output capacitor: A large enough capacitance to maintain a low ripple voltage, and a low ESR value in order to prevent high power dissipation due to RMS currents. The output capacitance can be approximated from the following equation: C6 ≥ where: I DC ≡ DC output current DV ≡ Output ripple I DC = = 0.348A assuming 5% peak to peak ripple, C6 ≥ = 81µF choose C6 = 100µF. I DC 2 π f LINE ∆V 80 230 0.348 2 π (60) (11.5) |
|
|
Link URL |
| Cho đến nay ALLDATASHEET có giúp ích cho doanh nghiệp của bạn hay không? [ DONATE ] |
Alldatasheet là | Quảng cáo | Liên lạc với chúng tôi | Chính sách bảo mật | Liên kết đến bảng dữ liệu | Trao đổi link | Tìm kiếm theo nhà sản xuất All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |