66056 datasheet(2/2 Pages) MICROPAC

2 / 2 page

MICROPAC INDUSTRIES, INC. OPTOELECTRONIC PRODUCTS DIVISION • 725 E. Walnut St.., Garland, TX 75040 • (972) 272-3571 • Fax (972) 487-6918

www.micropac.com

E-MAIL: optosales@micropac.com

3 - 35

66056

SINGLE/DUAL CHANNEL, HERMETICALLY SEALED, VERY HIGH SPEED OPTOCOUPLER

Rev 1

7/3/01

ELECTRICAL CHARACTERISTICS Ta=-55°C to at 125°C unless otherwise specified.

PARAMETER

SYMBOL

MIN

TYP

MAX

UNITS

TEST CONDITIONS

NOTE

High Level Output Current

IOH

5250

µA

VCC = 5.5V, VO = 5.5V,IF =250µA

Low Level Output Voltage

VOL

0.5

0.6

VCC = 5.5V, IF = 10mA

IOL (Sinking) = 10mA

1,3

High Level Supply Current

Single Channel

Dual Channel

ICCH

VCC = 5.5V, IF = 0

(Both Channels)

Low Level Supply Current

Single Channel

Dual Channel

ICCL

VCC = 5.5V, IF = 20mA

(Both Channels)

Input Forward Voltage

1.5

1.75

IF = 20mA

Input Reverse Breakdown Voltage

BVR

IR = 10µA

Input-Output Insulation Leakage Current

II—O

1.0

µA

VI—0 = 1500Vdc,

Relative Humidity = 45%

ta = 25°C, t = 5s

Propagation Delay Time To High Output Level

tPLH

100

RL = 510Ω, CL = 50pF.

If = 13mA, ta = 25°C

3,4

Propagation Delay Time To Low Output Level

tPHL

100

RL = 510Ω, CL = 50pF

If = 13mA, ta = 25°C

3,5

TYPICAL CHARACTERISTICS TA = 25°C, VCC = 5V EACH CHANNEL

PARAMETER

SYMBOL

MIN

TYP

MAX

UNITS

TEST CONDITIONS

NOTE

Input Capacitance

CIN

VF = 0, f = MHz

Input Diode Temperature Coefficient

∆vF ∆TA

-1.9

mV/°CIF = 20mA

Resistance (Input-Output)

RI-0

Ω

VI—O = 500V

Capacitance (Input-Output)

CI-O

f = 1MHz

Output Rise-Fall Time (10-90%)

tr, tf

RL = 510Ω, CL = 50pFIF = 13mA

Common Mode Transient Immunity at

High Output Level

CMH

1000

10000

V/µsVCM = 10V (peak),

VO (min) = 2V,

RL = 510Ω, IF = OmA

Common Mode Transient Immunity at

Low Output Level

CML

1000

10000

V/µsVCM = 10V (peak),

VO (max) = 0.8V,

RL = 510Ω, IF = 1OmA

NOTES:

Each channel

Measured between input pins shorted together and output pins shorted together.

It is essential that a bypass capacitor (.01 to 0.1µF ceramic) be connected from pin 1 to pin 4.

The tplh propagation delay is measured from the 6.5mA point on the trailing edge of the input pulse to the 1.5V point on the trailing edge of the output pulse.

The tphl propagation delay is measured from the 6.5mA point on the leading edge of the input pulse to the 1.5V point on the leading edge of the output pulse.

CMh is the max. tolerable common mode transient to assure that the output will remain in a high logic state (i.e. Vo >2.0V).

CMl is the max. tolerable common mode transient to assure that the output will remain in a low logic state (i.e. Vo < 0.8V).

RECOMMENDED OPERATING CONDITIONS:

PARAMETER

SYMBOL

MIN

MAX

UNITS

Input Current, Low Level Each Channel

IFL

0250

µA

Input Current, High Level Each Channel

IFH

12.5

Supply Voltage

4.5

5.5

Fan Out (TTL Load) Each Channel

Operating Temperature

-55

125

°C

SELECTION GUIDE

PART NUMBER

PART DESCRIPTION

66056-011

Single Channel, commercial optocoupler

66056-012

Dual Channel, commercial optocoupler

66056-001

Single Channel, Mil-temp optocoupler tested over full military temperature range (-55° to +125°C)

66056-002

Dual Channel, Mil-temp optocoupler tested over full military temperature range (-55° to +125°C)

66056-101

Single Channel optocoupler tested over full military temperature range with 100% device screening

66056-102

Dual Channel optocoupler tested over full military temperature range with 100% device screening

66056-103

DSCC Dwg 8102802PX Dual channel optocoupler

66056 bảng dữ liệu(PDF) 2 Page - Micropac Industries

66056 bảng dữ liệu(HTML) 2 Page - Micropac Industries

Html Pages

1 2

bảng dữ liệu tải về

Link URL