66013 datasheet(2/2 Pages) MICROPAC

2 / 2 page

MICROPAC INDUSTRIES, INC. OPTOELECTRONIC PRODUCTS DIVISION • 725 E. Walnut St., Garland, TX 75040 • (972) 272-3571 • Fax (972) 487-6918

www.micropac.com

E-MAIL: optosales@micropac.com

3 - 23

66013

DUAL CHANNEL, HERMETICALLY SEALED, HIGH SPEED 6N134 OPTOCOUPLER

ELECTRICAL CHARACTERISTICS

Ta=-55°C TO AT 125°C UNLESS OTHERWISE SPECIFIED.

PARAMETER

SYMBOL

MIN

TYP

MAX

UNITS

TEST CONDITIONS

NOTE

High Level Output Current

IOH

5250

µA

VCC = 5.5V, VO = 5.5V,

IF = 250µA

Low Level Output Voltage

VOL

0.35

0.6

VCC = 5.5V IF = 10mA

IOL(Sinking) = 10mA

1,9

High Level Supply Current

(Both Channels)

ICCH

VCC = 5.5V, IF = 0

Low Level Supply Current

(Both Channels)

ICCL

VCC = 5.5V, IF = 20mA

Input Forward Voltage

1.5

1.75

IF = 20mA

Input Reverse Breakdown Voltage

BVR

IR = 10µA

Input-Output Insulation Leakage Current

II—O

1.0

µA

VI—0 = 1500Vdc,

Relative Humidity = 45%

ta = 25

°C, t = 5s

Propagation Delay Time To High Output Level

tPLH

100

RL = 510Ω, CL = 50pF

If = 13mA, Ta = 25

°C

Propagation Delay Time To Low Output Level

tPHL

100

RL = 510Ω, CL = 50pF

If = 13mA, Ta = 25

°C

Delay Time To Low to High Output Level (90%)

tLH

RL = 510Ω, CL = 50pF

IF = 13mA, Ta = 25

°C

Delay Time To High to Low Output Level (90%)

tHL

RL = 510Ω, CL = 50pF

If = 13mA, Ta = 25

°C

TYPICAL CHARACTERISTICS TA = 25°C, VCC = 5V EACH CHANNEL

PARAMETER

SYMBOL

MIN

TYP

MAX

UNITS

TEST CONDITIONS

NOTE

Input Capacitance

CIN

VF = 0, f = MHz

Input Diode Temperature Coefficient

∆vF∆TA

-1.9

mV/°C

IF = 20mA

Resistance (Input-Output)

RI-0

Ω

VI—O = 500V

Capacitance (Input-Output)

CI-O

1.7

f = 1MHz

Input-Input Insulation Leakage Current

II-I

0.5

Relative Humidity = 45%

VI-I = 500V, t = 5s

Resistance (Input-Input)

RI-I

Ω

VI-I = 500V

Capacitance (Input-Input)

CI-I

0.80

f = 1MHz

Output Rise-Fall Time (10-90%)

tf, tf

RL = 510Ω, CL = 50pF

IF = 13mA

Common Mode Transient Immunity at High

Output Level

CMH

1000

10000

V/µsVCM = 10V (peak),

VO (min) = 2V,

RL = 510Ω, IF = OmA

Common Mode Transient Immunity at Low

Output Level

CML

1000

10000

V/µsVCM = 10V (peak),

VO (max) = 0.8V,

RL = 510Ω, IF = 10mA

NOTES:

Each channel

Measured between pins 1 through 8 shorted together and pins 9 through 16 shorted together.

Measured between pins 9 and 10 or 11 and 12 shorted together, and pins 9 through 16 shorted together.

Measured between pins 9 and 10 shorted together, and pins 11 and 12 shorted together.

The tplh propagation delay is measured from the 6.5mA point on the trailing edge of the input pulse to the 1.5V point on the trailing edge of the output pulse.

The tphl propagation delay is measured from the 6.5mA point on the leading edge of the input pulse to the 1.5V point on the leading edge of the output pulse.

CMh is the max. tolerable common mode transient to assure that the output will remain in a high logic state (i.e. Vo >2.0V).

CMl is the max. tolerable common mode transient to assure that the output will remain in a low logic state (i.e. Vo < 0.8V).

It is essential that a bypass capacitor (.01 to 0.1µF ceramic) be connected from pin 10 to pin 15.

RECOMMENDED OPERATING CONDITIONS:

PARAMETER

SYMBOL

MIN

MAX

UNITS

Input Current, Low Level Each Channel

IFL

0250

µA

Input Current, High Level Each Channel

IFH

12.5

Supply Voltage

4.5

5.5

SELECTION GUIDE

PART NUMBER

PART DESCRIPTION

66013-000

Dual Channel Optocoupler with 100% device screening

66013-001

DSCC Dwg 8102801EX Dual Channel Optocoupler

66013-002

Dual Channel Optocoupler, Commercial, tested over full military temperature range (-55°C to +125°C)

66013-003

Dual Channel Optocoupler, Commercial (0° to 70°C)

66013 bảng dữ liệu(PDF) 2 Page - Micropac Industries

66013 bảng dữ liệu(HTML) 2 Page - Micropac Industries

Html Pages

1 2

bảng dữ liệu tải về

Link URL