MCP2510-EST datasheet(46/76 Pages) MICROCHIP

46 / 76 page

MCP2510

DS21291C-page 46

Preliminary

 2000 Microchip Technology Inc.

7.6

Error Interrupt

When the error interrupt is enabled (CANINTE.ERRIE

= 1) an interrupt is generated on the INT pin if an over-

flow condition occurs or if the error state of transmitter

or receiver has changed. The Error Flag Register

(EFLG) will indicate one of the following conditions.

7.6.1

RECEIVER OVERFLOW

An overflow condition occurs when the MAB has assem-

bled a valid received message (the message meets the

criteria of the acceptance filters) and the receive buffer

associated with the filter is not available for loading of a

new message. The associated EFLG.RXNOVR bit will

be set to indicate the overflow condition. This bit must be

cleared by the MCU.

7.6.2

RECEIVER WARNING

The receive error counter has reached the MCU warn-

ing limit of 96.

7.6.3

TRANSMITTER WARNING

The transmit error counter has reached the MCU warn-

ing limit of 96.

7.6.4

RECEIVER ERROR-PASSIVE

The receive error counter has exceeded the error- pas-

sive limit of 127 and the device has gone to error- pas-

sive state.

7.6.5

TRANSMITTER ERROR-PASSIVE

The transmit error counter has exceeded the error-

passive limit of 127 and the device has gone to error-

passive state.

7.6.6

BUS-OFF

The transmit error counter has exceeded 255 and the

device has gone to bus-off state.

7.7

Interrupt Acknowledge

Interrupts are directly associated with one or more sta-

tus flags in the CANINTF register. Interrupts are pend-

ing as long as one of the flags is set. Once an interrupt

flag is set by the device, the flag can not be reset by the

MCU until the interrupt condition is removed.

CANINTE - Interrupt Enable Register (ADDRESS: 2Bh)

R/W-0

MERRE WAKIE

ERRIE

TX2IE

TX1IE

TX0IE

RX1IE

RX0IE

R = Readable bit

W = Writable bit

C = Bit can be cleared by

MCU but not set

U = Unimplemented -

reads as ‘0’

- n = Value at POR reset

bit 7

bit 0

bit 7:

MERRE: Message Error Interrupt Enable

0 = Disabled

1 = Interrupt on error during message reception or transmission

bit 6:

WAKIE: Wakeup Interrupt Enable

0 = Disabled

1 = Interrupt on CAN bus activity

bit 5:

ERRIE: Error Interrupt Enable (multiple sources in EFLG register)

0 = Disabled

1 = Interrupt on EFLG error condition change

bit 4:

TX2IE: Transmit Buffer 2 Empty Interrupt Enable

0 = Disabled

1 = Interrupt on TXB2 becoming empty

bit 3:

TX1IE: Transmit Buffer 1 Empty Interrupt Enable

0 = Disabled

1 = Interrupt on TXB1 becoming empty

bit 2:

TX0IE: Transmit Buffer 0 Empty Interrupt Enable

0 = Disabled

1 = Interrupt on TXB0 becoming empty

bit 1:

RX1IE: Receive Buffer 1 Full Interrupt Enable

0 = Disabled

1 = Interrupt when message received in RXB1

bit 0:

RX0IE: Receive Buffer 0 Full Interrupt Enable

0 = Disabled

1 = Interrupt when message received in RXB0

MCP2510-EST bảng dữ liệu(PDF) 46 Page - Microchip Technology

MCP2510-EST bảng dữ liệu(HTML) 46 Page - Microchip Technology

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76

bảng dữ liệu tải về

Link URL