LMP7715MFSLASHNOPB datasheet(3/27 Pages) TI

3 / 27 page

LMP7715, LMP7716, LMP7716Q

www.ti.com

SNOSAV0E – MARCH 2006 – REVISED MARCH 2013

2.5V Electrical Characteristics

Unless otherwise specified, all limits are ensured for TA = 25°C, V

+ = 2.5V, V− = 0V ,V

O = VCM = V

+/2. Boldface limits apply at

the temperature extremes.

Symbol

Parameter

Conditions

Min(1)

Typ(2)

Max(1)

Units

VOS

±20

±180

−20°C ≤ TA ≤ 85°C

±330

Input Offset Voltage

μV

±20

±180

−40°C ≤ TA ≤ 125°C

±430

TC VOS Input Offset Voltage Temperature

LMP7715

-1

±4

μV/°C

Drift(3)(4)

LMP7716/LMP7716Q

-1.75

−40°C ≤ TA ≤ 85°C

0.05

Input Bias Current

VCM = 1.0V

(4) (5)

−40°C ≤ TA ≤ 125°C

0.05

100

IOS

0.006

0.5

Input Offset Current

VCM = 1V

(4)

100

CMRR

Common Mode Rejection Ratio

≤ VCM ≤ 1.4V

PSRR

2.0V

≤ V+ ≤ 5.5V

100

V− = 0V, VCM = 0

Power Supply Rejection Ratio

1.8V

≤ V+ ≤ 5.5V

V− = 0V, VCM = 0

CMVR

CMRR

≥ 80 dB

−0.3

1.5

Common Mode Voltage Range

CMRR

≥ 78 dB

–0.3

1.5

AVOL

LMP7715, VO = 0.15 to 2.2V

RL = 2 kΩ to V

+/2

LMP7716/LMP7716Q, VO = 0.15 to 2.2V

RL = 2 kΩ to V

+/2

Open Loop Voltage Gain

LMP7715, VO = 0.15 to 2.2V

110

RL = 10 kΩ to V

+/2

LMP7716/ LMP7716Q, VO = 0.15 to 2.2V

RL = 10 kΩ to V

+/2

VOUT

RL = 2 kΩ to V

+/2

Output Voltage Swing

High

mV from

RL = 10 kΩ to V

+/2

either rail

RL = 2 kΩ to V

+/2

Output Voltage Swing

Low

RL = 10 kΩ to V

+/2

IOUT

Sourcing to V−

VIN = 200 mV

(6)

Output Current

Sinking to V+

7.5

VIN = −200 mV

(6)

5.0

0.95

1.30

LMP7715

1.65

Supply Current

1.10

1.50

LMP7716/LMP7716Q (per channel)

1.85

AV = +1, Rising (10% to 90%)

8.3

Slew Rate

μs

AV = +1, Falling (90% to 10%)

10.3

(1)

Limits are 100% production tested at 25°C. Limits over the operating temperature range are specified through correlations using the

Statistical Quality Control (SQC) method.

(2)

Typical values represent the most likely parametric norm as determined at the time of characterization. Actual typical values may vary

over time and will also depend on the application and configuration. The typical values are not tested and are not specified on shipped

production material.

(3)

Offset voltage average drift is determined by dividing the change in VOS at the temperature extremes by the total temperature change.

(4)

This parameter is specified by design and/or characterization and is not tested in production.

(5)

Positive current corresponds to current flowing into the device.

(6)

The short circuit test is a momentary open loop test.

Submit Documentation Feedback

Product Folder Links: LMP7715 LMP7716 LMP7716Q

LMP7715MF/NOPB bảng dữ liệu(PDF) 3 Page - Texas Instruments

LMP7715MF/NOPB bảng dữ liệu(HTML) 3 Page - Texas Instruments

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27

bảng dữ liệu tải về

Link URL