LM7341_15 datasheet(5/27 Pages) TI

5 / 27 page

LM7341

www.ti.com

SNOSAW9B – MAY 2008 – REVISED MARCH 2013

±15V Electrical Characteristics

Unless otherwise specified, all limits ensured for TA = 25°C, V

+ = 15V, V− = −15V, V

CM = VOUT = 0V and RL > 1 MΩ to 0V.

Boldface limits apply at the temperature extremes

Symbol

Parameter

Conditions

Min(1)

Typ(2)

Max(1)

Units

VOS

Input Offset Voltage

VCM = −14.5V and VCM = 14.5V

−4

±0.2

−5

TCVOS

Input Offset Voltage Temperature Drift

±2

μV/°C

Input Bias Current

VCM = −14.5V

−250

−110

−300

VCM = 14.5V

IOS

Input Offset Current

VCM = −14.5V and VCM = 14.5V

CMRR

Common Mode Rejection Ratio

−15V ≤ VCM ≤12V

115

−15V ≤ VCM ≤ 15V

100

PSRR

Power Supply Rejection Ratio

2.7V

≤ VS ≤ 30V, VCM = −14.5V

106

CMVR

Common Mode Voltage Range

CMRR > 80 dB

−15.3

−15.0

15.0

15.3

AVOL

Open Loop Voltage Gain

−13V ≤ VO ≤ 13V

200

V/mV

RL = 10 kΩ to 0V

VOUT

Output Voltage Swing

RL = 10 kΩ to 0V

135

300

High

VID = 100 mV

400

mV from

either rail

Output Voltage Swing

RL = 10 kΩ to 0V

160

300

Low

VID = −100 mV

400

IOUT

Output Current(3)

Sourcing, VOUT = −15V

VID = 200 mV

Sinking, VOUT = 15V

VID = −200 mV

Supply Current

VCM = −14.5V and VCM = 14.5V

0.7

1.2

1.3

Slew Rate

±12V Step

1.9

μs

GBW

Gain Bandwidth

f = 100 kHz, RL = 100 kΩ

4.6

MHz

Input Referred Voltage Noise Density

f = 1 kHz

nV/

√Hz

Input Referred Voltage Noise Density

f = 1 kHz

0.27

pA/

√Hz

THD+N

Total Harmonic Distortion + Noise

f = 10 kHz

−65

tPD

Propagation Delay

Overdrive = 50 mV(4)

µs

Overdrive = 1V(4)

Rise Time

20% to 80%(4)

µs

Fall Time

80% to 20%(4)

µs

(1)

All limits are specified by testing or statistical analysis.

(2)

Typical values represent the most likely parametric norm as determined at the time of characterization. Actual typical values may vary

over time and will also depend on the application and configuration. The typical values are not tested and are not ensured on shipped

production material.

(3)

The maximum power dissipation is a function of TJ(MAX), θJA. The maximum allowable power dissipation at any ambient temperature is

PD = (TJ(MAX) − TA)/θJA. All numbers apply for packages soldered directly unto a PC board.

(4)

The maximum differential voltage between the input pins is VIN Differential = ±15V.

Submit Documentation Feedback

Product Folder Links: LM7341

LM7341 bảng dữ liệu(PDF) 5 Page - Texas Instruments

LM7341 bảng dữ liệu(HTML) 5 Page - Texas Instruments

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27

bảng dữ liệu tải về

Link URL