MAX5911ESA datasheet(2/8 Pages) MAXIM

2 / 8 page

-48V Simple Swapper Hot-Swap Switches

_______________________________________________________________________________________

ABSOLUTE MAXIMUM RATINGS

ELECTRICAL SPECIFICATIONS

(VIN = -48V, AGND = DGND = 0, UVLO = open circuit, VENABLE = +3.3V, and TA = -40°C to +85°C, unless otherwise noted. Typical

values are at TA = +25°C.)

Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. These are stress ratings only, and functional

operation of the device at these or any other conditions beyond those indicated in the operational sections of the specifications is not implied. Exposure to

absolute maximum rating conditions for extended periods may affect device reliability.

VIN ..........................................................................+0.3V to -70V

VOUT ............................................................+0.3V to (VIN - 0.3V)

ENABLE to DGND ..................................................-0.3V to +11V

ENABLE to VIN .......................................................-0.3V to +70V

FAULT to DGND .....................................................-0.3V to +11V

UVLO to VIN............................................................-0.3V to +11V

DGND ..........................................................................-5V to +5V

DGND to VIN...........................................................-0.3V to +70V

FAULT Sink Current ............................................................10mA

Continuous Output Current ...............................Internally Limited

Continuous Power Dissipation (TA = +70°C)

8-Pin SO (derate 5.9mW/°C above +70°C)..................470mW

16-Pin SO (derate 12.9mW/°C above +70°C)...........1039mW

Operating Temperature Range ...........................-40°C to +85°C

Junction Temperature ......................................................+150°C

Storage Temperature Range .............................-60°C to +150°C

Lead Temperature (soldering, 10s) .................................+300°C

PARAMETER

SYMBOL

CONDITIONS

MIN

TYP

MAX

UNITS

Input Voltage Range

VIN

-65

-16

Supply Current

IIN

Measured at AGND at the end of output

voltage slew

1.5

2.5

MAX5911

-310

-280

-250

Maximum VOUT Current

IOUT(MAX)

VOUT = VIN + 5V

MAX5912

-457

-415

-373

DMOS On-Resistance

RDS(ON)

MAX5911 IOUT = -225mA,

MAX5912 IOUT = -350mA

2.5

Ω

VOUT Leakage Current

Measured on VOUT when internal DMOS is

shut off

µA

ENABLE Low Voltage

VIL

Referenced to DGND

0.8

ENABLE High Voltage

VIH

Referenced to DGND

2.0

ENABLE High Input Current

IIH

VENABLE = +3.3V

140

300

µA

ENABLE Low Pulse Width

(Note 1)

tEPW

200

FAULT Output Low Voltage

VOL

IFAULT = 3mA

0.4

FAULT Output Leakage Current

IOH

VFAULT = +3.3V

µA

Zero-Current Detection

Threshold

IFTH

Decreasing load current

-12

-8

-4

Zero-Current Detection

Threshold Hysteresis

IFHY

1.5

Zero-Current Detection Delay

(Note 2)

IFDEL

280

350

520

Current-Limit Delay (Note 3)

tLIMIT

VOUT shorted to AGND

µs

Power-Good Threshold

VPG

|VIN - VOUT|, |VIN - VOUT| decreasing

1.95

2.15

2.35

Power-Good Hysteresis

PGHYS

% of VPG

Voltages are with respect to AGND, unless otherwise noted.

MAX5911ESA bảng dữ liệu(PDF) 2 Page - Maxim Integrated Products

MAX5911ESA bảng dữ liệu(HTML) 2 Page - Maxim Integrated Products

Html Pages

1 2 3 4 5 6 7 8

bảng dữ liệu tải về

Link URL