TIP112 datasheet(2/8 Pages) ONSEMI

2 / 8 page

TIP110, TIP111, TIP112 (NPN); TIP115, TIP116, TIP117 (PNP)

www.onsemi.com

MAXIMUM RATINGS

Rating

Symbol

TIP110,

TIP115

TIP111,

TIP116

TIP112,

TIP117

Unit

Collector−Emitter Voltage

VCEO

100

Vdc

Collector−Base Voltage

VCB

100

Vdc

Emitter−Base Voltage

VEB

5.0

Vdc

Collector Current − Continuous

− Peak

2.0

4.0

Adc

Base Current

mAdc

Total Power Dissipation @ TC = 25°C

Derate above 25°C

0.4

W/°C

Total Power Dissipation @ TA = 25°C

Derate above 25°C

2.0

0.016

W/°C

Unclamped Inductive Load Energy − Figure 13

Operating and Storage Junction

TJ, Tstg

– 65 to + 150

°C

THERMAL CHARACTERISTICS

Characteristics

Symbol

Max

Unit

Thermal Resistance, Junction−to−Case

RqJC

2.5

°C/W

Thermal Resistance, Junction−to−Ambient

RqJA

62.5

°C/W

Stresses exceeding those listed in the Maximum Ratings table may damage the device. If any of these limits are exceeded, device functionality

should not be assumed, damage may occur and reliability may be affected.

ELECTRICAL CHARACTERISTICS (TC = 25°C unless otherwise noted)

Characteristic

Symbol

Min

Max

Unit

OFF CHARACTERISTICS

Collector−Emitter Sustaining Voltage (Note 1)

(IC = 30 mAdc, IB = 0)

TIP110, TIP115

TIP111, TIP116

TIP112, TIP117

VCEO(sus)

100

−

Vdc

Collector Cutoff Current

(VCE = 30 Vdc, IB = 0)

TIP110, TIP115

(VCE = 40 Vdc, IB = 0)

TIP111, TIP116

(VCE = 50 Vdc, IB = 0)

TIP112 ,TIP117

ICEO

−

2.0

mAdc

Collector Cutoff Current

(VCB = 60 Vdc, IE = 0)

TIP110, TIP115

(VCB = 80 Vdc, IE = 0)

TIP111, TIP116

(VCB = 100 Vdc, IE = 0)

TIP112, TIP117

ICBO

−

1.0

mAdc

Emitter Cutoff Current

(VBE = 5.0 Vdc, IC = 0)

IEBO

−

2.0

mAdc

ON CHARACTERISTICS (Note 1)

DC Current Gain

(IC = 1.0 Adc, VCE = 4.0 Vdc)

(IC = 2.0 Adc, VCE = 4.0 Vdc)

hFE

1000

500

−

Collector−Emitter Saturation Voltage (IC = 2.0 Adc, IB = 8.0 mAdc)

VCE(sat)

−

2.5

Vdc

Base−Emitter On Voltage (IC = 2.0 Adc, VCE = 4.0 Vdc)

VBE(on)

−

2.8

Vdc

DYNAMIC CHARACTERISTICS

Small−Signal Current Gain (IC = 0.75 Adc, VCE = 10 Vdc, f = 1.0 MHz)

hfe

−

Output Capacitance

(VCB = 10 Vdc, IE = 0, f = 0.1 MHz)

TIP115, TIP116, TIP117

TIP110, TIP111, TIP112

Cob

−

200

100

Product parametric performance is indicated in the Electrical Characteristics for the listed test conditions, unless otherwise noted. Product

performance may not be indicated by the Electrical Characteristics if operated under different conditions.

1. Pulse Test: Pulse Width v 300 ms, Duty Cycle v 2%.

TIP112 bảng dữ liệu(PDF) 2 Page - ON Semiconductor

TIP112 bảng dữ liệu(HTML) 2 Page - ON Semiconductor

Html Pages

1 2 3 4 5 6 7 8

bảng dữ liệu tải về

Link URL