11

LT1787/LT1787HV

Dimensions in inches (millimeters) unless otherwise noted.

S8 Package

8-Lead Plastic Small Outline (Narrow 0.150)

(LTC DWG # 05-08-1610)

MSOP (MS8) 1098

* DIMENSION DOES NOT INCLUDE MOLD FLASH, PROTRUSIONS OR GATE BURRS. MOLD FLASH,

PROTRUSIONS OR GATE BURRS SHALL NOT EXCEED 0.006" (0.152mm) PER SIDE

** DIMENSION DOES NOT INCLUDE INTERLEAD FLASH OR PROTRUSIONS.

INTERLEAD FLASH OR PROTRUSIONS SHALL NOT EXCEED 0.006" (0.152mm) PER SIDE

0.021

± 0.006

(0.53

± 0.015)

0

° – 6° TYP

SEATING

PLANE

0.007

(0.18)

0.040

± 0.006

(1.02

± 0.15)

0.012

(0.30)

REF

0.006

± 0.004

(0.15

± 0.102)

0.034

± 0.004

(0.86

± 0.102)

0.0256

(0.65)

BSC

12

3

4

0.193

± 0.006

(4.90

± 0.15)

8

7 6

5

0.118

± 0.004*

(3.00

± 0.102)

0.118

± 0.004**

(3.00

± 0.102)

MS8 Package

8-Lead Plastic MSOP

(LTC DWG # 05-08-1660)

Information furnished by Linear Technology Corporation is believed to be accurate and reliable.

However, no responsibility is assumed for its use. Linear Technology Corporation makes no represen-

tation that the interconnection of its circuits as described herein will not infringe on existing patent rights.

0.016 – 0.050

(0.406 – 1.270)

0.010 – 0.020

(0.254 – 0.508)

× 45°

0

°– 8° TYP

0.008 – 0.010

(0.203 – 0.254)

SO8 1298

0.053 – 0.069

(1.346 – 1.752)

0.014 – 0.019

(0.355 – 0.483)

TYP

0.004 – 0.010

(0.101 – 0.254)

0.050

(1.270)

BSC

1

2

3

4

0.150 – 0.157**

(3.810 – 3.988)

8

7

6

5

0.189 – 0.197*

(4.801 – 5.004)

0.228 – 0.244

(5.791 – 6.197)

DIMENSION DOES NOT INCLUDE MOLD FLASH. MOLD FLASH

SHALL NOT EXCEED 0.006" (0.152mm) PER SIDE

DIMENSION DOES NOT INCLUDE INTERLEAD FLASH. INTERLEAD

FLASH SHALL NOT EXCEED 0.010" (0.254mm) PER SIDE

*

**

Adjusting Gain Setting

The LT1787 may be used in all operating modes with an

LT1787’s transconductance, 400

µA/V typical. A nominal

gain of 40 may be obtained with an external 100k resistor

The transconductance gm is set by on-chip resistors on

the LT1787. These resistors match well but have loose

absolute tolerance. This will normally require that the

external gain setting resistor be trimmed for initial accu-

racy. After trimming, the temperature stability of the gm

and therefore gain will be –200ppm/

°C.

The only limitations placed upon the resistor choice is care

must be taken not to saturate the internal circuitry by