LT1394CS8 datasheet(11/16 Pages) LINER

11 / 16 page

LT1394

APPLICATIONS INFORMATION

correct, amplified composite signal at the LT1394’s posi-

tive input in Trace D. The LT1394’s output is Trace E. Figure

9 details circuit propagation delay. The output responds in

18ns to a 500

µV overdrive on a 1mV step. Figure 10 plots

response time versus overdrive. As might be expected,

propagation delay decreases at higher overdrives. A1’s

noise limits usable sensitivity.

A1 has poorly defined DC characteristics, necessitating

some form of DC correction. A2 and A3, operating at a

differential gain of 100, provide this function. They differ-

entially sense a band limited version of A1’s inputs and feed

DC and low frequency amplified information to the com-

parator. The low frequency roll-off of A1’s signal path

complements A2-A3’s high frequency roll-off. The sum-

mation of these two signal channels at the LT1394 inputs

results in flat response from DC to high frequency.

Figure 8 shows waveforms for the high gain comparator.

Trace A is a 500

µV overdrive on a 1mV step applied to the

circuit’s positive input (negative input grounded). Trace B

shows the resulting amplified step at A1’s positive output.

Trace C is A2’s band limited output. A1’s wideband output

combines with A2’s DC corrected information to yield the

µs/DIV

1394 F08

A = 1mV/DIV

10ns/DIV

1394 F09

A = 1mV/DIV

B = 1V/DIV

B = 0.1V/DIV

(AC-COUPLED)

C = 0.1V/DIV

D = 0.1V/DIV

E = 5V/DIV

Figure 8. 500

µV Input (Trace A) Is Split into Wideband

and Low Frequency Gain Paths (Traces B and C) and

Recombined (Trace D). Comparator Output Is Trace E

Figure 9. Parallel Path Comparator Shows 18ns

Response (Trace B) to 500

µV Overdrive (Trace A)

RESPONSE TIME (ns)

1100

1000

900

800

700

600

500

1394 F10

Figure 10. Response Time vs Overdrive for the

Composite Comparator

Voltage-Controlled Delay

The ability to set a precise, predictable delay has broad

application in pulse circuitry. Figure 11’s configuration

sets a 0 to 300ns delay from a corresponding 0V to 3V

control voltage. It takes advantage of the LT1394’s speed

and the clean dynamics of an emitter switched current

source.

Q1 and Q2 form a current source that charges the 1000pF

capacitor. When the trigger input is high (Trace A, Figure

12) both Q3 and Q4 are on. The current source is off and

Q2’s collector (Trace B) is at ground. The latch input at the

LT1394 prevents it from responding and its output remains

high. When the trigger input goes low, the LT1394’s latch

input is disabled and its output drops low. Q4’s collector

(Trace C) lifts and Q2 comes on, delivering constant

current to the 1000pF capacitor (Trace B). The resulting

linear ramp at the LT1394’s positive input is compared to

the delay programming voltage input. When a crossing

occurs, the comparator goes high (Trace D). The length of

time the comparator was low is directly proportional to the

LT1394CS8 bảng dữ liệu(PDF) 11 Page - Linear Technology

LT1394CS8 bảng dữ liệu(HTML) 11 Page - Linear Technology

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16

bảng dữ liệu tải về

Link URL