LT1362CS datasheet(5/12 Pages) LINER

5 / 12 page

LT1361/LT1362

SYMBOL

PARAMETER

CONDITIONS

VSUPPLY

MIN

TYP

MAX

UNITS

VOUT

Output Swing

RL = 1k, VIN = ±40mV

±15V

13.4

±V

RL = 500Ω, VIN = ±40mV

±15V

12.0

±V

RL = 500Ω, VIN = ±40mV

±5V

3.4

±V

RL = 150Ω, VIN = ±40mV

±5V

3.0

±V

RL = 500Ω, VIN = ±40mV

±2.5V

1.2

±V

IOUT

Output Current

VOUT = ±12.0V

±15V

VOUT = ±3.0V

±5V

ISC

Short-Circuit Current

VOUT = 0V, VIN = ±3V

±15V

Slew Rate

AV = – 2, (Note 5)

±15V

450

µs

±5V

175

µs

GBW

Gain Bandwidth

f = 200kHz

±15V

MHz

±5V

MHz

Channel Separation

VOUT = ±10V, RL = 500Ω±15V

Supply Current

Each Amplifier

±15V

6.0

Each Amplifier

±5V

5.8

TYPICAL PERFORMANCE CHARACTERISTICS

Input Common Mode Range vs

Supply Voltage

SUPPLY VOLTAGE (

±V)

015

1361/1362 G01

–55

°C

125

°C

Supply Current vs Supply Voltage

and Temperature

Input Bias Current vs

Input Common Mode Voltage

INPUT COMMON MODE VOLTAGE (V)

0.2

0.1

0.6

0.5

0.4

0.3

–15

–10

–5

1361/1362 G03

VS = ±15V

TA = 25°C

IB =



+ + I

–

————

Note 1: Absolute Maximum Ratings are those values beyond which the life

of a device may be impaired.

Note 2: Differential inputs of

±10V are appropriate for transient operation

only, such as during slewing. Large, sustained differential inputs will cause

excessive power dissipation and may damage the part. See Input

Considerations in the Applications Information section of this data sheet

for more details.

Note 3: A heat sink may be required to keep the junction temperature

below absolute maximum when the output is shorted indefinitely.

Note 4: Input offset voltage is pulse tested and is exclusive of warm-up drift.

Note 5: Slew rate is measured between

±10V on the output with ±6V input

for

±15V supplies and ±1V on the output with ±1.75V input for ±5V supplies.

Note 6: Full power bandwidth is calculated from the slew rate

measurement: FPBW = SR/2

πVP.

Note 7: This parameter is not 100% tested.

Note 8: The LT1361C/LT1362C are guaranteed functional over the

operating temperature range of –40

°C to 85°C.

Note 9: The LT1361C/LT1362C are guaranteed to meet specified

performance from 0

°C to 70°C. The LT1361C/LT1362C are designed,

characterized and expected to meet specified performance from – 40

°C to

°C, but are not tested or QA sampled at these temperatures. For

guaranteed I-grade parts, consult the factory.

SUPPLY VOLTAGE (

±V)

V –

2.0

0.5

1.0

1.5

V +

–1.0

– 0.5

–2.0

–1.5

015

1361/1362 G02

TA = 25°C

∆VOS < 1mV

ELECTRICAL CHARACTERISTICS The q denotes the specifications which apply over the temperature range

–40

°C ≤ TA ≤ 85°C, VCM = 0V unless otherwise noted. (Note 9)

LT1362CS bảng dữ liệu(PDF) 5 Page - Linear Technology

LT1362CS bảng dữ liệu(HTML) 5 Page - Linear Technology

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12

bảng dữ liệu tải về

Link URL