| công cụ tìm kiếm bảng dữ liệu linh kiện điện tử |
|
LT3591 bảng dữ liệu(PDF) 8 Page - Linear Technology |
|
|
|||||||||||||||||||||||||||||
LT3591 bảng dữ liệu(HTML) 8 Page - Linear Technology |
|
8 / 16 page ![]() LT3591 8 3591f APPLICATIONS INFORMATION SCHOTTKY DIODE The LT3591 has a built-in Schottky diode. The internal schottky saves board space in space constrained appli- cations. In less space sensitive applications, an external schottky diode connected between the SW node and the CAP node increases efficiency one to two percent. It is important to use a properly rated schottky diode that can handle the peak switch current of the LT3591. In addition, the schottky diode must have a breakdown voltage of at least 40V along with a low forward voltage in order to achieve higher efficiency. One recommended external schottky diode for the LT3591 is the Phillips PMEG4005AEA. OVERVOLTAGE PROTECTION The LT3591 has an internal open-circuit protection circuit. In the cases of output open circuit, when the LEDs are disconnected from the circuit or the LEDs fail open circuit, VCAP is clamped at 42V (typ). The LT3591 will then switch at a very low frequency to minimize input current. The VCAP and input current during output open circuit are shown in the Typical Performance Characteristics. Figure 4 shows the transient response when the LEDs are disconnected. For low DCR inductors, which is usually the case for this application, the peak inrush current can be simplified as follows: I V L r L LC PK IN = ⎛ ⎝⎜ ⎞ ⎠⎟ = = –. • • exp – • • • – 06 2 2 1 ω α ω π α ω rr L 2 2 4• where L is the inductance, r is the DCR of the inductor and C is the output capacitance. Table 3 gives inrush peak currents for some component selections. Table 3. Inrush Peak Currents VIN (V) r (Ω)L (µH) COUT (µF) IP (A) 4.2 0.3 22 2.2 1.06 4.2 0.71 22 2.2 0.96 4.2 0.58 15 1 0.83 4.2 1.6 15 1 0.68 PROGRAMMING LED CURRENT The feedback resistor (RSENSE) and the sense voltage (VCAP – VLED) control the LED current. The CTRL pin controls the sense reference voltage as shown in the Typical Performance Characteristics. For CTRL higher than 1.5V, the sense reference is 200mV, which results in full LED current. In order to have accurate LED current, precision resistors are preferred (1% is rec- ommended). The formula and table for RSENSE selection are shown below. R mV I SENSE LED = 200 VCAP 20V/DIV IL 500mA/DIV VIN = 3.6V CIRCUIT OF FRONT PAGE APPLICATION LEDs DISCONNECTED AT THIS INSTANT 500 µs/DIV 3591 F04 Figure 4. Output Open-Circuit Waveform INRUSH CURRENT The LT3591 has a built-in Schottky diode. When supply voltage is applied to the VIN pin, an inrush current flows through the inductor and the Schottky diode and charges up the CAP voltage. The Schottky diode inside the LT3591 can sustain a maximum current of 1A. |
|
|
Link URL |
| Cho đến nay ALLDATASHEET có giúp ích cho doanh nghiệp của bạn hay không? [ DONATE ] |
Alldatasheet là | Quảng cáo | Liên lạc với chúng tôi | Chính sách bảo mật | Liên kết đến bảng dữ liệu | Trao đổi link | Tìm kiếm theo nhà sản xuất All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |