| công cụ tìm kiếm bảng dữ liệu linh kiện điện tử |
|
LTC3429B bảng dữ liệu(PDF) 5 Page - Linear Technology |
|
|
|||||||||||||||||||||||||||||
LTC3429B bảng dữ liệu(HTML) 5 Page - Linear Technology |
|
5 / 12 page ![]() LTC3429/LTC3429B 5 3429fa PI FU CTIO S SW (Pin 1): Switch Pin. Connect inductor between SW and VIN. Keep these PCB trace lengths as short and wide as possible to reduce EMI and voltage overshoot. If the inductor current falls to zero, or SHDN is low, an internal 150Ω antiringing switch is connected from SW to VIN to minimize EMI. GND (Pin 2): Signal and Power Ground. Provide a short direct PCB path between GND and the (–) side of the output capacitor(s). FB (Pin 3): Feedback Input to the gm Error Amplifier. Connect resistor divider tap to this pin. The output voltage can be adjusted from 2.5V to 5V by: VOUT = 1.23V • [1 + (R1/R2)] SHDN (Pin 4): Logic Controlled Shutdown Input. SHDN = High: Normal free running operation, 500kHz typical operating frequency. SHDN = Low: Shutdown, quiescent current < 1µA. Output capacitor can be completely discharged through the load or feedback resistors. A 150Ω resistor is internally connected between SW and VIN. VOUT (Pin 5): Output Voltage Sense Input and Drain of the Internal Synchronous Rectifier MOSFET. Bias is derived from VOUT. PCB trace length from VOUT to the output filter capacitor(s) should be as short and wide as possible. VOUT is completely disconnected from VIN when SHDN is low due to the output disconnect feature. VIN (Pin 6): Battery Input Voltage. The device gets its start-up bias from VIN. Once VOUT exceeds VIN, bias comes from VOUT. Thus, once started, operation is com- pletely independent from VIN. Operation is only limited by the output power level and the battery’s internal series resistance. 1.23V REF Burst Mode OPERATION CONTROL SHUTDOWN CONTROL SLOPE COMP PWM CONTROL START-UP OSC MUX A B A/B RAMP GEN 500kHz FB 3429 BD 3 VOUT VIN L1 5 SW 0.45Ω WELL SWITCH 1 VIN 1V TO 4.4V 6 SHDN 4 GND 2 gm ERROR AMP VOUT GOOD PWM COMPARATOR RC 80k SHUTDOWN CC 150pF CP2 2.5pF R2 R1 SLEEP Σ SYNC DRIVE CONTROL 0.35Ω 2.3V COUT CPL (OPTIONAL) 2.5V TO 5V CIN + CURRENT SENSE BLOCK DIAGRA |
|
|
Link URL |
| Cho đến nay ALLDATASHEET có giúp ích cho doanh nghiệp của bạn hay không? [ DONATE ] |
Alldatasheet là | Quảng cáo | Liên lạc với chúng tôi | Chính sách bảo mật | Liên kết đến bảng dữ liệu | Trao đổi link | Tìm kiếm theo nhà sản xuất All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |