| công cụ tìm kiếm bảng dữ liệu linh kiện điện tử |
|
AN2708 bảng dữ liệu(PDF) 11 Page - STMicroelectronics |
|
|
|||||||||||||||||||||||||||||
AN2708 bảng dữ liệu(HTML) 11 Page - STMicroelectronics |
|
11 / 42 page ![]() AN2708 High-frequency ballast 11/42 Note: Resistors are 0.25 W unless specified. Q1, Q2 &Q3 are mounted with 8 °C/W heatsink. 2.1 PFC converter This block allows drawing a quasi-sinusoidal current from the mains, in phase with the line voltage in order to get a PF very close to 1 (more than 0.99). To achieve such high PF the boost topology is implemented because of the advantages it offers: ● Minimum number of external components, thus making it a low-cost solution ● Low input di/dt thus minimizing the noise generated at the input and, therefore, the requirements on the input EMI filter ● The switch is source-grounded, therefore is easy to drive However, boost topology requires the DC output voltage (400 Vdc) to be higher than the maximum expected line peak voltage. ST's L6562 has been used as the driver. It implements a transition mode control (fixed ON time, variable frequency), that, for such output power, is preferred to the fixed frequency average current mode being simpler and cheaper. The circuit operates on the boundary between continuous and discontinuous current mode. Besides providing good results in terms of power factor, this IC considerably reduces the Total Harmonic Distortion (THD) as it reduces the conduction dead-angle that occurs to the AC input current near the zero-crossings of the line voltage. R100 68 k Ω 1% SMD resistor 0805 R24_1,R24_ 2 680 k Ω Resistor R30_1,R30_ 2 100 k Ω 2 W resistor T1 Transformer Choke boost inductor (ITACOIL E2543/E) U1 L6562N STMicroelectronics transition-mode PFC controller U2 L6574 STMicroelectronics ballast driver U7 LE50CZ TO-92 STMicroelectronics very low drop voltage regulators U8 VIPer12A-E DIP8 STMicroelectronics offline SMPS primary IC 730 V 0.4 A 27R U9,U10 SFH6156-2 Optocoupler U11 ST7FDALIF2M6 SO20 STMicroelectronics 8-bit MCU with single voltage Flash memory, data EEPROM, ADC, timers, SPI, DALI Table 3. Ballast bill of material (continued) Reference Value Description |
|
Link URL |
| Cho đến nay ALLDATASHEET có giúp ích cho doanh nghiệp của bạn hay không? [ DONATE ] |
Alldatasheet là | Quảng cáo | Liên lạc với chúng tôi | Chính sách bảo mật | Liên kết đến bảng dữ liệu | Trao đổi link | Tìm kiếm theo nhà sản xuất All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |