ISL84516 datasheet(3/10 Pages) INTERSIL

3 / 10 page

Absolute Maximum Ratings

Thermal Information

V+ to V- . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -0.3 to 15V

Input Voltages

IN (Note 2). . . . . . . . . . . . . . . . . . . . . ((V-) - 0.3V) to ((V+) + 0.3V)

NO, NC (Note 2) . . . . . . . . . . . . . . . . ((V-) - 0.3V) to ((V+) + 0.3V)

Output Voltages

COM (Note 2) . . . . . . . . . . . . . . . . . . ((V-) - 0.3V) to ((V+) + 0.3V)

Continuous Current (Any Terminal) . . . . . . . . . . . . . . . . . . . . . 20mA

Peak Current NO, NC, or COM

(Pulsed 1ms, 10% Duty Cycle, Max) . . . . . . . . . . . . . . . . . . 30mA

ESD Rating (Per MIL-STD-883 Method 3015). . . . . . . . . . . . . >2kV

Operating Conditions

Temperature Range

ISL8451XIX . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -40oC to 85oC

Thermal Resistance (Typical, Note 3)

θJA (oC/W)

5 Ld SOT-23 Package . . . . . . . . . . . . . . . . . . . . . . .

225

8 Ld SOIC Package . . . . . . . . . . . . . . . . . . . . . . . . .

170

Maximum Junction Temperature (Plastic Package) . . . . . . . 150oC

Moisture Sensitivity (See Technical Brief TB363)

All Packages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Level 1

Maximum Storage Temperature Range. . . . . . . . . . . . -65oC to 150oC

Maximum Lead Temperature (Soldering 10s) . . . . . . . . . . . . 300oC

(Lead Tips Only)

CAUTION: Stresses above those listed in “Absolute Maximum Ratings” may cause permanent damage to the device. This is a stress only rating and operation of the

device at these or any other conditions above those indicated in the operational sections of this specification is not implied.

NOTES:

2. Signals on NO, NC, COM, or IN exceeding V+ or V- are clamped by internal diodes. Limit forward diode current to maximum current ratings.

θJA is measured with the component mounted on a low effective thermal conductivity test board in free air. See Tech Brief TB379 for details.

Electrical Specifications -

±5V Supply Test Conditions: V

SUPPLY = ±4.5V to ±5.5V, VINH = 3.5V, VINL = 1.5V (Note 4),

Unless Otherwise Specified

PARAMETER

TEST CONDITIONS

TEMP

(oC)

(NOTE 5)

MIN

TYP

(NOTE 5)

MAX

UNITS

ANALOG SWITCH CHARACTERISTICS

Analog Signal Range, VANALOG

Full

V-

V+

ON Resistance, RON

VS = ±5V, ICOM = 1.0mA, VCOM = 3V

(See Figure 4)

Ω

Full

Ω

RON Flatness, RFLAT(ON)

VS = ±5V, ICOM = 1.0mA, VCOM = -3V, 0V, 3V

Ω

Full

Ω

NO or NC OFF Leakage Current,

INO(OFF) or INC(OFF)

VS = ±5.5V, VCOM = ±4.5V, VNO or VNC = +4.5V

(Note 6)

-1

0.01

Full

-20

COM OFF Leakage Current,

ICOM(OFF)

VS = ±5.5V, VCOM = ±4.5V, VNO or VNC = +4.5V

(Note 6)

-1

0.01

Full

-20

COM ON Leakage Current,

ICOM(ON)

VS = ±5.5V, VCOM = VNO or VNC = ±4.5V (Note 6)

-2

0.01

Full

-40

DIGITAL INPUT CHARACTERISTICS

Input Voltage High, VINH

Full

(V+) - 1.5

V+

Input Voltage Low, VINL

Full

V-

(V+) - 3.5

Input Current, IINH, IINL

VS = ±5.5V, VIN = 0V or V+

Full

-0.5

0.5

µA

DYNAMIC CHARACTERISTICS

Turn-ON Time, tON

VNO or VNC = 3V, RL = 300Ω, CL = 35pF,

VIN = 0 to V+ (See Figure 1)

100

Full

150

Turn-OFF Time, tOFF

VNO or VNC = 3V, RL = 300Ω, CL = 35pF,

VIN = 0 to V+ (See Figure 1)

Full

125

Charge Injection, Q

CL = 1.0nF, VG = 0V, RG = 0Ω (See Figure 2)

OFF Isolation

RL = 50Ω, CL = 15pF, f = 100kHz (See Figure 3)

>86

NO or NC OFF Capacitance, COFF f = 1MHz, VNO or VNC = VCOM = 0V (See Figure 5)

COM OFF Capacitance,

CCOM(OFF)

f = 1MHz, VNO or VNC = VCOM = 0V (See Figure 5)

COM ON Capacitance, CCOM(ON)

f = 1MHz, VNO or VNC = VCOM = 0V (See Figure 5)

ISL84516, ISL84517

ISL84516 bảng dữ liệu(PDF) 3 Page - Intersil Corporation

ISL84516 bảng dữ liệu(HTML) 3 Page - Intersil Corporation

Html Pages

1 2 3 4 5 6 7 8 9 10

bảng dữ liệu tải về

Link URL