HIP9022AM datasheet(5/10 Pages) INTERSIL

5 / 10 page

4-5

Absolute Maximum Ratings

Thermal Information

Maximum Analog Supply Voltage, VDD . . . . . . . . . . . -0.3V to 14V

Logic Supply Voltage, VCC . . . . . . . . . . . . . . . . . . . . . . -0.3V to 6V

Analog Negative Supply Voltage, VEE . . . . . . . . . . . . . 0.3V to -5.5

Maximum Laser Protection Diode Current . . . . . . . . . . 10A, 200ns

Operating Conditions

VDD Supply Voltage Range, VDD . . . . . . . . . . . . . . 11.4V to 12.6V

VCC Supply Voltage Range, VCC . . . . . . . . . . . . . . . . 4.5V to 5.5V

VEE Supply Voltage Range, VEE . . . . . . . . . . . . . . . . -4.5V to -5.5V

Laser Power Supply Range, VLAS . . . . . . . . . . . . . . . . . . 3V to 5V

TEC Power Supply Range, VTEC . . . . . . . . . . . . . . . . . . . 3V to 5V

Laser Operating Current Range, IDL . . . . . . . . . . . . . . . . . 0A to 2A

TEC Operating Current Range, ITEC . . . . . . . . . . . . . . . . . 0A to 2A

Thermal Resistance (Typical, Note 1)

θJC(oC/W)

PLCC Package . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Maximum Operating Junction Temperature, TJ . . . . . . . . . . . 100

Maximum Storage Temperature Range, TSTG . . . . -55

oC to 150oC

Maximum Lead Temperature (Soldering 10s) . . . . . . . . . . . . 300oC

Die Characteristics

Back Side Potential . . . . . . . . . . . . . . . . . . . . . . . . . -VEE, Substrate

CAUTION: Stresses above those listed in “Absolute Maximum Ratings” may cause permanent damage to the device. This is a stress only rating and operationofthe

device at these or any other conditions above those indicated in the operational sections of this speciﬁcation is not implied.

NOTE:

θJA is measured with the component mounted on an evaluation PC board in free air.

Electrical Speciﬁcations

TJ = 100οC, VDD = 12V, VCC = 5V, VEE = -5V, INVERT Low (Figure 1 Conﬁguration)

Unless Otherwise Speciﬁed

PARAMETER

SYMBOL

TEST CONDITIONS

MIN

TYP

MAX

UNITS

POWER SUPPLIES

V9P Voltage, No External Load

V9P

µF Tantalum

Capacitor to V9P

-9-

V9P Thermal Shutdown

150

V9P Thermal Shutdown Recovery

125

V9P Current Limiting

VDD Power Supply Current

IDD

-25

VCC Power Supply Current

ICC

1.5

VEE Power Supply Current

IEE

-75

-23

LOGIC/DIGITAL INPUTS

(A0-A3, NULLB and SB_H, LASERON1B, LASERON2B with 60k

Ω Pullup Resistors; INVERT, RESETB, RLY_IN 60kΩ

with Pulldown Resistors)

Low Level Input Voltage

VIL

1.5

High Level Input Voltage

VIH

3.5

VCC + 0.3

Minimum Hysteresis

VHYS

0.3

Low Level Input Current (Inputs with Pullups)

IIL

-140

µA

High Level Input Current (Inputs with Pulldowns)

IIH

140

µA

CONSTANT CURRENT CONTROLLER

OTA Gate Drive Amp. (A2) Voltage Output Range

-4

VCC

Current Monitor Amp. (A1) Gain

AVS

9.8

10.2

Current Monitor Amp. Differential Sense Input Range

VIN

500

Current Monitor Amp. Input Offset

VIO

-5

Current Monitor Amp. Common Mode Input Range

VIC

0-5

SHUNT CURRENT SWITCH CONTROLLER

(Note 2) VUPPER = 2V, VLOWER = -1V, Gate Load = 5000pF, VUP1, 2; 1µF Filter Capacitor to

GND, VLOW1, 2; 1

µF Filter Capacitor to GND, Unless Otherwise Speciﬁed

Shunt Gate Output Rise/Fall time

tR/tF

10% -90% Rise,

90% -10% Fall

Propagation Delay, LASERONB1, 2 to SG_1, 2

TJ = 100

110

TJ = -25

o C

Drive Output Voltage

VUPPER

VCC

VLOWER

-4

VCC

HIP9022

HIP9022AM bảng dữ liệu(PDF) 5 Page - Intersil Corporation

HIP9022AM bảng dữ liệu(HTML) 5 Page - Intersil Corporation

Html Pages

1 2 3 4 5 6 7 8 9 10

bảng dữ liệu tải về

Link URL