HIP0050IB datasheet(3/7 Pages) INTERSIL

3 / 7 page

HIP0050

Absolute Maximum Ratings

Thermal Information

Output Voltage, VOUT (Note 1) . . . . . . . . . . . . . . . . . . . -0.3V to VOC

Input Voltage, VIN . . . . . . . . . . . . . . . . . . . . . . . . -0.3V to VCC +0.3V

Logic Supply Voltage, VCC . . . . . . . . . . . . . . . . . . . . . . -0.3V to +7V

Max Output Load Current, ILOAD (Per Output, Note 2) . . . . . . . . . ICL

Max. Output Load Current, ILOAD (All Outputs ON, Note 2) . . . . . 2A

Operating Ambient Temperature Range, TA . . . . . . . . -40

oC to 85oC

Operating Junction Temperature Range. . . . . . . . . . -40oC to 150oC

Storage Temperature Range, TSTG . . . . . . . . . . . . . -55

oC to 150oC

Maximum Lead Temperature (Soldering 10s Max). . . . . . . . . 300oC

(Lead Tips Only)

CAUTION: Stresses above those listed in “Absolute Maximum Ratings” may cause permanent damage to the device. This is a stress only rating and operation

of the device at these or any other conditions above those indicated in the operational sections of this speciﬁcation is not implied.

Operating Conditions

Typical Logic Supply Voltage, VCC . . . . . . . . . . . . . . . . . . . . . . +5V

ICC Supply Current, with 200mA each Output . . . . . . . . . . . . 2mA

ICC Supply Current, with No Load . . . . . . . . . . . . . . . . . . . . . 2mA

Input Low Voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.0V

Input High Voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3.5V

Power Output Driver Voltage Range . . . . . . . . . . . . . . . . . 0 to VOC

Power Output Driver Current Load, IDR. . . . . . . . . . . . . . . . 0 to ICL

Typical Output rDSON Channel Resistance . . . . . . . . . . . . . . . . 2Ω

Typical Output Rise Time . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

µs

Typical Output Fall Time . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

µs

Electrical Speciﬁcations

VCC = 4.5V to 5.5V, VBATT = 8V to 16V, TA = -40

oC to 85oC; Unless Otherwise Speciﬁed

PARAMETER

SYMBOL

CONDITIONS

MIN

TYP

MAX

UNITS

OUTPUTS DRIVERS (DR0 TO DR7)

Output Channel Resistance

rDSON

Output Current = 200mA, TA =85

4.0

Ω

Output Over-Current Shutdown

Threshold

ICL

300

500

Output Clamping Voltage

VOC

Outputs OFF

Output Clamping Energy

EOC

1ms Single Pulse Width, TA = 25

oC,

(Refer to Figure 2 for SOA).

-25-

Output OFF Leakage Current

IOFF

Output Voltage = 40V, TA =85

oC-

µA

Output Rise Time

tRISE

Load = 75

Ω, 0.01µF (Parallel)

0.5

µs

Output Fall Time

tFALL

Load = 75

Ω, 0.01µF (Parallel)

0.5

µs

Output Delay from Strobe, High

to Low Output Transition

tDHL

µs

Output Delay from Strobe, Low to

High Output Transition

tDLH

0.2

2.6

µs

LOGIC SUPPLY

Logic Supply Current, Loaded

ICC

All Outputs ON, 0.2A Load Per Output

Logic Supply Current, No Load

ICC

All Outputs OFF

Logic Supply Under-Voltage

Reset Threshold

All Outputs OFF

3.5

LOGIC INPUTS (EN, SI, SCK, STR)

Threshold Voltage at Falling

Edge

VT-VCC = 5V ±10%

0.2VCC

0.3VCC

-V

Threshold Voltage at Rising

Edge

VT+VCC = 5V ±10%

0.6VCC

0.7VCC

Hysteresis Voltage

VT+ - VT-

0.85

1.4

2.25

Leakage Current

ILIN

-10

µA

SERIAL DATA CLOCK (SCK) (Refer to Figure 1 for Waveform Detail)

Frequency

fSCK

1.6

MHz

Pulse Width High

tW(SCKH)

175

Package

JC (

oC/W)†

JA (

oC/W)††

PDIP . . . . . . . . . . . . .

SOIC . . . . . . . . . . . . .

†

Versus Additional Square Inches 1oz. copper on PCB.

†† Standard Test Board, 0.002 diameter T/C located at lead

shoulder, middle lead.

HIP0050IB bảng dữ liệu(PDF) 3 Page - Intersil Corporation

HIP0050IB bảng dữ liệu(HTML) 3 Page - Intersil Corporation

Html Pages

1 2 3 4 5 6 7

bảng dữ liệu tải về

Link URL