ICS1893 datasheet(63/152 Pages) ICST

63 / 152 page

Chapter 8

Management Register Set

ICS1893 Rev C 6/6/00

June, 2000

ICS1893 - Release

8.2

Table 8-5 lists the bits for the Control Register, a 16-bit register used to establish the basic operating

modes of the ICS1893.

• The Control Register is accessible through the MII Management Interface.

• Its operation is independent of the MAC/Repeater Interface configuration.

• It is fully compliant with the ISO/IEC Control Register definition.

Note:

For an explanation of acronyms used in Table 8-5, see Chapter 1, “Abbreviations and Acronyms”.

† Whenever the PHY address of Table 8-16:

• Is equal to 00000 (binary), the Isolate bit 0.10 is logic one.

• Is not equal to 00000, the Isolate bit 0.10 is logic zero.

‡ As per the IEEE Std 802.3u, during any write operation to any bit in this register, the STA must write the default value

to all Reserved bits.

8.2.1

Reset (bit 0.15)

This bit controls the software reset function. Setting this bit to logic one initiates an ICS1893 software reset

during which all Management Registers are set to their default values and all internal state machines are

set to their idle state. For a detailed description of the software reset process, see Section 5.1.2.3,

“Software Reset”.

During reset, the ICS1893 leaves bit 0.15 set to logic one and isolates all STA management register

accesses. However, the reset process is not complete until bit 0.15 (a Self-Clearing bit), is set to logic zero,

which indicates the reset process is terminated.

Table 8-5.

Control Register (Register 0 [0x00]

Bit

Definition

When Bit = 0

When Bit = 1

Ac-

cess

De-

fault

Hex

0.15

Reset

No effect

ICS1893 enters Reset

mode

R/W

0.14

Loopback enable

Disable Loopback mode

Enable Loopback mode

R/W

–

0.13

Data rate select

10 Mbps operation

100 Mbps operation

R/W

–

0.12

Auto-Negotiation enable

Disable Auto-Negotiation

Enable Auto-Negotiation

R/W

–

0.11

Low-power mode

Normal power mode

Low-power mode

R/W

–

0/4†

0.10

Isolate

No effect

Isolate ICS1893 from MII

R/W

–

0/1†

0.9

Auto-Negotiation restart

No effect

Restart Auto-Negotiation

R/W

0.8

Duplex mode

Half-duplex operation

Full-duplex operation

R/W

–

0.7

Collision test

No effect

Enable collision test

R/W

–

0.6

IEEE reserved

Always 0

N/A

–

0‡

0.5

IEEE reserved

Always 0

N/A

–

0‡

0.4

IEEE reserved

Always 0

N/A

–

0‡

0.3

IEEE reserved

Always 0

N/A

–

0‡

0.2

IEEE reserved

Always 0

N/A

–

0‡

0.1

IEEE reserved

Always 0

N/A

–

0‡

0.0

IEEE reserved

Always 0

N/A

–

0‡

ICS1893 bảng dữ liệu(PDF) 63 Page - Integrated Circuit Systems

ICS1893 bảng dữ liệu(HTML) 63 Page - Integrated Circuit Systems

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

bảng dữ liệu tải về

Link URL