| công cụ tìm kiếm bảng dữ liệu linh kiện điện tử |
|
FA7622CP bảng dữ liệu(PDF) 5 Page - Fuji Electric |
|
|
|||||||||||||||||||||||||||||
FA7622CP bảng dữ liệu(HTML) 5 Page - Fuji Electric |
|
5 / 8 page ![]() FA7622CP(E) 5 • Inverting chopper circuit According to the circuit shown in Fig. 5, the power output voltage VOUTB can be determined as follows: VOUTB = – R11 R10 (5) .............................. • VREF The AV between the VOUTB and FB2 pins can be determined as follows: AV –R11 R12 (6) ................................................. To correct the phase, connect the resistor R13 and capacitor C3 in series between the IN2– and FB2 pins. By using this circuit, invert the output polarity of OUT2 with an external transistor to drive a P-channel MOSFET (or PNP transistor). 3. PWM comparator section As Fig. 6 shows, a PWM comparator has three input terminals. PWM comparator 1 determines the duty cycle of the output from the OUT1 pin. This comparator compares the CT oscillator Voltage (Pin 1) with the FB1 voltage (Pin 17) or the DT1 voltage (Pin 16), whichever is greater. When the highest of these voltages is lower than the CT voltage, the PWM output is high. When it is higher than CT, the PWM output is low. PWM comparator 2 determines the duty cycle of the output from the OUT2 pin. To determine the PWM output, this comparator compares the CT oscillator voltage (Pin 1) with the FB2 voltage (Pin 6) or the DT2 voltage (Pin 7) whichever is higher. During ordinary operation, the OUT1 and OUT2 pin voltages have the same polarity as the output from each comparator. When the power supply is turned on, the pulse width gradually increases. The time constant for soft-start is determined by the external resistor and capacitor across pins 16 and 7. In Figures 7 and 8, the time ts required for the pulse width (duty-cycle) to reach about 30% after start-up can be determined as follows: (Units: µF for Cs and kΩ for Rs, Rs1, and Rs2) Fig. 5 Fig. 8 Fig. 6 C3 Q3 FB2 R10 R9 REF R11 R12 R13 IN2 IN2 ER.AMP2 VCC1 + - V OUTB (Controlled by Q3) 10 20 6 5 4 OUT2 PWM output FB1(FB2) DT1(DT2) Time CT PWM output PWM1 (PWM2) DT1(DT2) FB1(FB2) CT Fig. 7 DT1(DT2) 20 1 FB1(FB2) CS CT RS REF PWM output PWM1 (PWM2) 20 1 DT1(DT2) FB1(FB2) CS CT RS2 REF PWM output PWM1 (PWM2) RS1 Fig.8: tS (mS) = CS • ln RS1 0.417RS1 – 0.583 RS2 (7) ................................. Fig.7: tS (mS) = 0.54CS • RS Where, RS1 / RS2 > 0.716 (8) …… RS1 • RS2 RS1 RS2 Please connect enough large capacitance between REF and GND pins in order to prevent irregular output pulse caused by minus voltage at DT1 or DT2 pin when IC is shut down. |
|
|
Link URL |
| Cho đến nay ALLDATASHEET có giúp ích cho doanh nghiệp của bạn hay không? [ DONATE ] |
Alldatasheet là | Quảng cáo | Liên lạc với chúng tôi | Chính sách bảo mật | Liên kết đến bảng dữ liệu | Trao đổi link | Tìm kiếm theo nhà sản xuất All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |