| công cụ tìm kiếm bảng dữ liệu linh kiện điện tử |
|
LM48821TLEVAL bảng dữ liệu(PDF) 17 Page - Texas Instruments |
|
|
|||||||||||||||||||||||||||||
LM48821TLEVAL bảng dữ liệu(HTML) 17 Page - Texas Instruments |
|
17 / 24 page ![]() LM48821, LM48821TLEVAL www.ti.com SNAS354 – JUNE 2007 I2C INTERFACE POWER SUPPLY PIN (I2CVDD) The LM48821’s I2C interface is powered up through the I2CVDD pin. The LM48821’s I 2C interface operates at a voltage level set by the I2CVDD pin. This voltage can be independent from the main power supply pin (VDD). This is ideal whenever logic levels for the I2C interface are dictated by a microcontroller or microprocessor that is operating at a lower supply voltage than the main battery of a portable system. POWER SUPPLY BYPASSING As with any power amplifier, proper supply bypassing is critical for low noise performance and high power supply rejection. Applications that employ a 3.3V voltage regulator typically use a 10 μF in parallel with a 0.1μF filter capacitors to stabilize the regulator’s output, reduce noise on the regulated supply lines, and improve the regulator’s transient response. However, their presence does not eliminate the need for a local 1.0 μF tantalum bypass capacitance connected between the LM48821’s supply pins and ground. Keep the length of leads and traces that connect capacitors between the LM48821’s power supply pins and ground as short as possible. ELIMINATING THE OUTPUT COUPLING CAPACITOR The LM48821 features a low noise inverting charge pump that generates an internal negative supply voltage. This allows the LM48821 to reference its amplifier outputs to ground instead of a half-supply voltage, like traditional capacitivel-coupled headphone amplifiers. Because there is no DC bias voltage associated with either stereo output, the large DC blocking capacitors (typically 220 μF) are not necessary. The coupling capacitors are replaced by two, small ceramic charge pump capacitors, saving board space and cost. Eliminating the output coupling capacitors also improves low frequency response. In traditional headphone amplifiers, the headphone impedance and the output capacitor form a high pass filter that not only blocks the DC component of the output, but also attenuates low frequencies, impacting the bass response. Because the LM48821 does not require the output coupling capacitors, the low frequency response of the device is not degraded. In addition to eliminating the output coupling capacitors, the ground referenced output nearly doubles the output voltage swing and available dynamic range of the LM48821 when compared to a traditional capacitively-coupled output headphone amplifier operating from the same supply voltage. OUTPUT TRANSIENT ELIMINATED The LM48821 contains advanced circuitry that virtually eliminates output transients (’clicks' and 'pops’). This circuitry attenuates output transients when the supply voltage is first applied or when the part resumes operation after using the shutdown mode. POWER DISSIPATION Power dissipation is a major concern when using any power amplifier and must be thoroughly understood to ensure a successful design. Equation 1 states the maximum power dissipation point for a single-ended amplifier operating at a given supply voltage and driving a specified output load. PDMAX = (2VDD) 2 / (2π2R L) (1) Since the LM48821 has two power amplifiers in one package, the maximum internal power dissipation point is twice that of the number which results from Equation 1. Even with large internal power dissipation, the LM48821 does not require heat sinking over a large range of ambient temperatures. The maximum power dissipation point obtained must not be greater than the power dissipation that results from Equation 2: PDMAX = (TJMAX - TA) / (θJA) (2) For the DSBGA package, θJA = 105°C/W. TJMAX = 150°C for the LM48821. Depending on the ambient temperature, TA, of the system surroundings, Equation 2 can be used to find the maximum internal power dissipation supported by the IC packaging. If the result of Equation 1 is greater than that of Equation 2, then either the supply voltage must be decreased, the load impedance increased or TA reduced. Power dissipation is a function of output power and thus, if typical operation is not around the maximum power dissipation point, the ambient temperature may be increased accordingly. Copyright © 2007, Texas Instruments Incorporated Submit Documentation Feedback 17 Product Folder Links: LM48821 LM48821TLEVAL |
|
|
Link URL |
| Cho đến nay ALLDATASHEET có giúp ích cho doanh nghiệp của bạn hay không? [ DONATE ] |
Alldatasheet là | Quảng cáo | Liên lạc với chúng tôi | Chính sách bảo mật | Liên kết đến bảng dữ liệu | Trao đổi link | Tìm kiếm theo nhà sản xuất All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |