MASW-009482 datasheet(2/7 Pages) MA-COM

2 / 7 page

GaAs Broadband High Power SP3T Switch

DC - 4.0 GHz

Rev. V1

MASW-009482

•

North America Tel: 800.366.2266 • Europe Tel: +353.21.244.6400

•

India Tel: +91.80.43537383

•

China Tel: +86.21.2407.1588

Visit www.macomtech.com for additional data sheets and product information.

M/A-COM Technology Solutions Inc. and its affiliates reserve the right to make

changes to the product(s) or information contained herein without notice.

ADVANCED: Data Sheets contain information regarding a product M/A-COM Technology Solutions

is considering for development. Performance is based on target specifications, simulated results,

and/or prototype measurements. Commitment to develop is not guaranteed.

PRELIMINARY: Data Sheets contain information regarding a product M/A-COM Technology

Solutions has under development. Performance is based on engineering tests. Specifications are

typical. Mechanical outline has been fixed. Engineering samples and/or test data may be available.

Commitment to produce in volume is not guaranteed.

Electrical Specifications: TA = 25°C, Z0 = 50 Ω, VC = 0 V / 2.7 V, 1000 pF Capacitors

4. External DC blocking capacitors are required on all RF ports. Typical performance specifications are with 1000 pF blocking and decoupling

capacitors / as shown on the application schematic .

5. RX Interferer power set to –10 dBm during test to improve dynamic range of measurement system. Typical performance with –23 dBm

interferer is determined by using a linear relationship between interferer power level and cross modulation products.

Parameter

Test Conditions

Units

Min.

Typ.

Max.

Insertion Loss

(All Paths)

1.0 GHz

2.0 GHz

2.5 GHz

—

0.55

0.75

0.7

0.9

Isolation

1.0 GHz

2.0 GHz

2.5 GHz

—

Return Loss

(All RF ports)

DC - 2.5 GHz

—

Input IP3

Two Tone, +23 dBm/tone, 5 MHz Spacing, 1 GHz

Two Tone, +23 dBm/tone, 5 MHz Spacing, 2 GHz

dBm

—

Cross Modulation

For Cell Band: Two-tone signal input:

TX1 = +22 dBm @ 820 MHz, TX2 = +22 dBm @ 821 MHz,

RX interferer = -23 dBm @ 865 MHz

dBm

—

-108

—

For PCS Band: Two-tone signal input:

TX1 = +18 dBm @ 1880 MHz, TX2 = +18 dBm @ 1881 MHz,

RX interferer = -23 dBm @ 1960 MHz

dBm

—

-109

—

Input P0.1dB

VC = 0 V/2.7 V, 1 GHz

dBm

—

Trise, Tfall

10% to 90% RF, 90% to 10% RF, 900 MHz

—

Ton, Toff

50% control to 90% RF, and 50% control to 10% RF,

900 MHz

—

Transients

In Band

—

Control Current

VC = 0 V/2.7 V

µA

—

rd Harmonic

Fin = 1 GHz, Pin = +26 dBm

Fin = 2 GHz, Pin = +26 dBm

dBc

—

nd Harmonic

Fin = 1 GHz, Pin = +26 dBm

Fin = 2 GHz, Pin = +26 dBm

dBc

—

Truth Table 8,9

ANT-RF1 ANT-RF2 ANT-RF3

Off

8. Differential voltage, V (state 1) -V (state 0) must be 2.6 V

minimum and must not exceed 8.5 V.

9. Positive Control: 1 = +2.6 V to +8.0 V, 0 = 0 V +/- 0.2V

Negative Control: 1 = 0 V +/- 0.2V, 0 = -2.6 V to -8.0 V

Parameter

Absolute Maximum

Input Power

(0.5 - 4.0 GHz, 2.6 V Control)

+36 dBm

Control Voltage

±8.5 volts

Operating Temperature

-40

°C to +85°C

Storage Temperature

-65

°C to +150°C

Absolute Maximum Ratings 6,7

6. Exceeding any one or combination of these limits may cause

permanent damage to this device.

7. M/A-COM Technology does not recommend sustained

operation near these survivability limits.

MASW-009482 bảng dữ liệu(PDF) 2 Page - M/A-COM Technology Solutions, Inc.

MASW-009482 bảng dữ liệu(HTML) 2 Page - M/A-COM Technology Solutions, Inc.

Html Pages

1 2 3 4 5 6 7

bảng dữ liệu tải về

Link URL