công cụ tìm kiếm bảng dữ liệu linh kiện điện tử
  Vietnamese  ▼
ALLDATASHEET.VN

X  

DS2405P bảng dữ liệu(PDF) 11 Page - Dallas Semiconductor

tên linh kiện DS2405P
Giải thích chi tiết về linh kiện  Addressable Switch
PDF  15 Pages
Scroll/Zoom Zoom In 100%  Zoom Out
nhà sản xuất  DALLAS [Dallas Semiconductor]
Trang chủ  https://www.maximintegrated.com/en.html
Logo DALLAS - Dallas Semiconductor

DS2405P bảng dữ liệu(HTML) 11 Page - Dallas Semiconductor

Back Button DS2405P Datasheet HTML 7Page - Dallas Semiconductor DS2405P Datasheet HTML 8Page - Dallas Semiconductor DS2405P Datasheet HTML 9Page - Dallas Semiconductor DS2405P Datasheet HTML 10Page - Dallas Semiconductor DS2405P Datasheet HTML 11Page - Dallas Semiconductor DS2405P Datasheet HTML 12Page - Dallas Semiconductor DS2405P Datasheet HTML 13Page - Dallas Semiconductor DS2405P Datasheet HTML 14Page - Dallas Semiconductor DS2405P Datasheet HTML 15Page - Dallas Semiconductor  
Zoom Inzoom in Zoom Outzoom out
 11 / 15 page
background image
DS2405
11 of 15
102299
Skip ROM [CCh]
The complete 1-Wire protocol for all Dallas Semiconductor iButtons contains a Skip ROM command.
Since the DS2405 contains only the 64-bit ROM with no additional data fields, the Skip ROM is not
applicable and will cause no further activity on the 1-Wire bus if executed. The DS2405 does not interfere
with other 1-Wire parts on a multidrop bus that do respond to a Skip ROM (for example, a DS2405 and
DS1994 on the same bus).
1-WIRE SIGNALING
The DS2405 requires strict protocols to ensure data integrity. The protocol consists of four types of
signaling on one line: reset sequence with Reset Pulse and Presence Pulse, write 0, write 1 and read data.
All these signals except Presence Pulse are initiated by the bus master.
The initialization sequence required to begin any communication with the DS2405 is shown in Figure 5.
A Reset Pulse followed by a Presence Pulse indicates the DS2405 is ready to send or receive data given
the correct ROM command.
The bus master transmits (TX) a Reset Pulse (tRSTL, minimum 480
µs). The bus master then releases the
line and goes into receive mode (RX). The 1-Wire bus is pulled to a high state via the 5 k
Ω pullup
resistor. After detecting the rising edge on the data pin, the DS2405 waits (tPDH, 15-60
µs) and then
transmits the Presence Pulse (tPDL, 60-240
µs).
INITIALIZATION PROCEDURE “RESET AND PRESENCE PULSES” Figure 5
480
µs ≤t
RSTL <
∞*
480
µs ≤t
RSTH <
∞ (includes recovery time)
15
µs ≤t
PDH < 60
µs
60
µs ≤t
PDL < 240
µs
∗ In order not to mask interrupt signaling by other devices on the 1-Wire bus, t
RSTL + tR should always
be less than 960
µs.
RESISTOR
MASTER
DS2405



Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15


bảng dữ liệu tải về

Go To PDF Page


Link URL



Cho đến nay ALLDATASHEET có giúp ích cho doanh nghiệp của bạn hay không?  [ DONATE ] 

Alldatasheet là   |   Quảng cáo   |   Liên lạc với chúng tôi   |   Chính sách bảo mật   |   Liên kết đến bảng dữ liệu    |   Trao đổi link   |   Tìm kiếm theo nhà sản xuất
All Rights Reserved©Alldatasheet.com


Mirror Sites
English : Alldatasheet.com  |   English : Alldatasheet.net  |   Chinese : Alldatasheetcn.com  |   German : Alldatasheetde.com  |   Japanese : Alldatasheet.jp
Russian : Alldatasheetru.com  |   Korean : Alldatasheet.co.kr  |   Spanish : Alldatasheet.es  |   French : Alldatasheet.fr  |   Italian : Alldatasheetit.com
Portuguese : Alldatasheetpt.com  |   Polish : Alldatasheet.pl  |   Vietnamese : Alldatasheet.vn
Indian : Alldatasheet.in  |   Mexican : Alldatasheet.com.mx  |   British : Alldatasheet.co.uk  |   New Zealand : Alldatasheet.co.nz
Family Site : ic2ic.com  |   icmetro.com