| công cụ tìm kiếm bảng dữ liệu linh kiện điện tử |
|
US5C3257G-S16-R bảng dữ liệu(PDF) 4 Page - Unisonic Technologies |
|
|
|||||||||||||||||||||||||||||
US5C3257G-S16-R bảng dữ liệu(HTML) 4 Page - Unisonic Technologies |
|
4 / 6 page ![]() US5C3257 Preliminary CMOS IC UNISONICTECHNOLOGIESCO.,LTD 4 of 6 www.unisonic.com.tw QW-R502-891.a ABSOLUTE MAXIMUM RATING PARAMETER SYMBOL RATINGS UNIT Supply Voltage to Ground Potential (Inputs & VCC Only) -0.5~+7.0 V Supply Voltage to Ground Potential (Outputs & D/O Only) -0.5~+7.0 V DC Input Voltage -0.5~+7.0 V DC Output Current 120 mA Power Dissipation PD 0.5 W Storage Temperature TSTG -55~+150 °C Ambient Temperature with Power Applied TOPR -40~+85 °C Note: Absolute maximum ratings are those values beyond which the device could be permanently damaged. Absolute maximum ratings are stress ratings only and functional device operation is not implied. DC ELECTRICAL CHARACTERISTICS (Typical application at VCC=5 V, TA=25°C, unless otherwise noted) PARAMETER SYMBOL TEST CONDITIONS (Note 1) MIN TYP (Note 1) MAX UNIT Input HIGH Voltage VIH Guaranteed Logic HIGH Level 2.0 V Input LOW Voltage VIL Guaranteed Logic LOW Level -0.5 0.8 V Input HIGH Current IIH VCC=Max., VIN=VCC ±1 µA Input LOW Current IIL VCC=Max., VIN=GND ±1 µA High Impedance Output Current IOZH 0≤I, Y≤VCC ±1 µA Clamp Diode Voltage VIK VCC=Min., IIN=-18mA -0.7 -1.2 V Short Circuit Current (Note 2) IOS I(Y)=0V, Y(I)=VCC 100 mA Input Hysteresis at Control Pins VH 150 mV Switch On Resistance (Note 3) RON VCC=Min., VIN=0.0V, ION=48mA 5 7 Ω VCC=Min., VIN=2.4V, ION=15mA 10 15 Ω CAPACITANCE (TA=25°C, f=1MHz) PARAMETER (Note 4) SYMBOL TEST CONDITIONS MIN TYP MAX UNIT Input Capacitance CIN VIN=0V 6 pF In/Yn Capacitance, Switch Off COFF VIN=0V 6 pF In/Yn Capacitance, Switch On CON VIN=0V 14 pF Notes:1. Typical values are at VCC=5.0V, TA=25°C ambient and maximum loading. 2. Not more than one output should be shorted at one time. Duration of the test should not exceed one second. 3. Measured by the voltage drop between I and Y pin at indicated current through the switch. ON resistance is determined by the lower of the voltages on the two (I, Y) pins. 4. This parameter is determined by device characterization but is not production tested. |
|
|
Link URL |
| Cho đến nay ALLDATASHEET có giúp ích cho doanh nghiệp của bạn hay không? [ DONATE ] |
Alldatasheet là | Quảng cáo | Liên lạc với chúng tôi | Chính sách bảo mật | Liên kết đến bảng dữ liệu | Trao đổi link | Tìm kiếm theo nhà sản xuất All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |