| công cụ tìm kiếm bảng dữ liệu linh kiện điện tử |
|
RF13 bảng dữ liệu(PDF) 29 Page - Renesas Technology Corp |
|
|
|||||||||||||||||||||||||||||
RF13 bảng dữ liệu(HTML) 29 Page - Renesas Technology Corp |
|
29 / 56 page ![]() RL78 Family Chapter 4 Using EEPROM Emulation EEPROM Emulation Library Pack02 R01US0068EJ0100 Rev.1.00 Page 29 of 53 Mar. 28, 2014 (1) Operation frequency This sets an operation frequency which is used in RL78 microcontrollers. Note1 The setting value is set to the FDL_Init frequency parameter by the following expressions (The frequency is calculated by raising its decimals. The result calculated omits its decimals.). Setting value of FDL_Init operation frequency = ((FDL_SYSTEM_FREQUENCY + 999999)/1000000) Ex.1: When FDL_SYSTEM_FREQUENCY is 20000000 (20 MHz), ((20000000 + 999999)/10000000) = 20.999999 = 20 Ex.2: When FDL_SYSTEM_FREQUENCY is 4500000 (4.5 MHz), ((4500000 + 999999)/10000000) = 5.499999 = 5 Ex.3: When FDL_SYSTEM_FREQUENCY is 5000001 (5.000001 MHz), ((5000001 + 999999)/10000000) = 6.000000 = 6 Note1: This setting is a value required to control data flash memory. This setting does not change the operation frequency of RL78 microcontrollers. In addition, this operation frequency is not the frequency of the high-speed on-chip oscillator. (2) Voltage mode Note 2 This sets the voltage mode of data flash memory. Note 3 When FDL_WIDE_VOLTAGE_MODE is not defined: Full-speed mode When FDL_WIDE_VOLTAGE_MODE is defined: Wide voltage mode Note 2: The FDL_WIDE_VOLTAGE_MODE is commented out and not defined in the initial setting. To use RL78 microcontrollers in the wide voltage mode, cancel the comment-out to define the mode. Note 3: For details of the voltage mode, see the corresponding RL78 microcontrollers user’s manual. (3) FDL pool size Specify 0. (4) EEL pool size Note 4 The number of blocks in the data flash memory of the target device must be specified as the number of blocks in the EEL pool. Note 4: Specify 3 (3 blocks) or a greater value (recommended). (5) Number of stored data items Specify the number of data items to be used in the EEPROM emulation. A value of 1 to 64 can be set. |
|
Link URL |
| Cho đến nay ALLDATASHEET có giúp ích cho doanh nghiệp của bạn hay không? [ DONATE ] |
Alldatasheet là | Quảng cáo | Liên lạc với chúng tôi | Chính sách bảo mật | Liên kết đến bảng dữ liệu | Trao đổi link | Tìm kiếm theo nhà sản xuất All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |