AT89 datasheet(3/22 Pages) ATMEL

3 / 22 page

AT89C52

4-63

The AT89C52 provides the following standard features: 8K

bytes of Flash, 256 bytes of RAM, 32 I/O lines, three 16-bit

timer/counters, a six-vector two-level interrupt architecture,

a full duplex serial port, on-chip oscillator, and clock cir-

cuitry. In addition, the AT89C52 is designed with static logic

for operation down to zero frequency and supports two

software selectable power saving modes. The Idle Mode

stops the CPU while allowing the RAM, timer/counters,

serial port, and interrupt system to continue functioning.

The Power Down Mode saves the RAM contents but

freezes the oscillator, disabling all other chip functions until

the next hardware reset.

Pin Description

VCC

Supply voltage.

GND

Ground.

Port 0

Port 0 is an 8-bit open drain bidirectional I/O port. As an

output port, each pin can sink eight TTL inputs. When 1s

are written to port 0 pins, the pins can be used as high-

impedance inputs.

Port 0 can also be configured to be the multiplexed low-

order address/data bus during accesses to external pro-

gram and data memory. In this mode, P0 has internal pul-

lups.

Port 0 also receives the code bytes during Flash program-

ming and outputs the code bytes during program verifica-

tion. External pullups are required during program verifica-

tion.

Port 1

Port 1 is an 8-bit bidirectional I/O port with internal pullups.

The Port 1 output buffers can sink/source four TTL inputs.

When 1s are written to Port 1 pins, they are pulled high by

the internal pullups and can be used as inputs. As inputs,

Port 1 pins that are externally being pulled low will source

current (IIL) because of the internal pullups.

In addition, P1.0 and P1.1 can be configured to be the

timer/counter 2 external count input (P1.0/T2) and the

timer/counter 2 trigger input (P1.1/T2EX), respectively, as

shown in the following table.

Port 1 also receives the low-order address bytes during

Flash programming and verification.

Port 2

Port 2 is an 8-bit bidirectional I/O port with internal pullups.

The Port 2 output buffers can sink/source four TTL inputs.

When 1s are written to Port 2 pins, they are pulled high by

the internal pullups and can be used as inputs. As inputs,

Port 2 pins that are externally being pulled low will source

current (IIL) because of the internal pullups.

Port 2 emits the high-order address byte during fetches

from external program memory and during accesses to

external data memory that use 16-bit addresses (MOVX @

DPTR). In this application, Port 2 uses strong internal pul-

lups when emitting 1s. During accesses to external data

memory that use 8-bit addresses (MOVX @ RI), Port 2

emits the contents of the P2 Special Function Register.

Port 2 also receives the high-order address bits and some

control signals during Flash programming and verification.

Port 3

Port 3 is an 8-bit bidirectional I/O port with internal pullups.

The Port 3 output buffers can sink/source four TTL inputs.

When 1s are written to Port 3 pins, they are pulled high by

the internal pullups and can be used as inputs. As inputs,

Port 3 pins that are externally being pulled low will source

current (IIL) because of the pullups.

Port 3 also serves the functions of various special features

of the AT89C51, as shown in the following table.

Port 3 also receives some control signals for Flash pro-

gramming and verification.

RST

Reset input. A high on this pin for two machine cycles while

the oscillator is running resets the device.

ALE/PROG

Address Latch Enable is an output pulse for latching the

low byte of the address during accesses to external mem-

ory. This pin is also the program pulse input (PROG) during

Flash programming.

In normal operation, ALE is emitted at a constant rate of 1/6

the oscillator frequency and may be used for external tim-

ing or clocking purposes. Note, however, that one ALE

Port Pin

Alternate Functions

P1.0

T2 (external count input to Timer/Counter 2),

clock-out

P1.1

T2EX (Timer/Counter 2 capture/reload trigger

and direction control)

Port Pin

Alternate Functions

P3.0

RXD (serial input port)

P3.1

TXD (serial output port)

P3.2

INT0 (external interrupt 0)

P3.3

INT1 (external interrupt 1)

P3.4

T0 (timer 0 external input)

P3.5

T1 (timer 1 external input)

P3.6

WR (external data memory write strobe)

P3.7

RD (external data memory read strobe)

AT89 bảng dữ liệu(PDF) 3 Page - ATMEL Corporation

AT89 bảng dữ liệu(HTML) 3 Page - ATMEL Corporation

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22

bảng dữ liệu tải về

Link URL