| công cụ tìm kiếm bảng dữ liệu linh kiện điện tử |
|
AT27BV1024 bảng dữ liệu(PDF) 2 Page - ATMEL Corporation |
|
|
|||||||||||||||||||||||||||||
AT27BV1024 bảng dữ liệu(HTML) 2 Page - ATMEL Corporation |
|
2 / 9 page ![]() Atmel’s innovative design techniques provide fast speeds that rival 5V parts while keeping the low power consump- tion of a 3V supply. At VCC = 2.7V, any word can be ac- cessed in less than 120 ns. With a typical power dissipa- tion of on ly 18 mW at 5 MH z and VCC = 3 V , th e AT27BV1024 consumes less than one fifth the power of a standard 5V EPROM. Standby mode supply current is typically less than 1 µA at 3V. The AT27BV1024 simplifies system design and stretches battery lifetime even further by eliminating the need for power supply regulation. The AT27BV1024 is available in industry standard JEDEC-approved one-time programmable (OTP) plastic PLCC and TSOP packages. All devices feature two-line control (CE, OE) to give designers the flexibility to prevent bus contention. The AT27BV1024 operating with VCC at 3.0V produces TTL level outputs that are compatible with standard TTL logic devices operating at VCC = 5.0V. At VCC = 2.7V, the part is compatible with JEDEC approved low voltage bat- tery operation (LVBO) interface specifications. The device is also capable of standard 5-volt operation making it ide- ally suited for dual supply range systems or card products that are pluggable in both 3-volt and 5-volt hosts. Atmel’s AT27BV1024 has additional features to ensure high quality and efficient production use. The Rapid™ Pro- gramming Algorithm reduces the time required to program the part and guarantees reliable programming. Program- ming time is typically only 100 µs/word. The Integrated Product Identification Code electronically identifies the de- vice and manufacturer. This feature is used by industry standard programming equipment to select the proper programming algorithms and voltages. The AT27BV1024 programs exactly the same way as a standard 5V AT27C1024 and uses the same programming equipment. Description (Continued) Switching between active and standby conditions via the Chip Enable pin may produce transient voltage excur- sions. Unless accommodated by the system design, these transients may exceed data sheet limits, resulting in de- vice non-conformance. At a minimum, a 0.1 µF high fre- quency, low inherent inductance, ceramic capacitor should be utilized for each device. This capacitor should be connected between the VCC and Ground terminals of the device, as close to the device as possible. Additionally, to stabilize the supply voltage level on printed circuit boards with large EPROM arrays, a 4.7 µF bulk electrolytic capacitor should be utilized, again connected between the VCC and Ground terminals. This capacitor should be posi- tioned as close as possible to the point where the power supply is connected to the array. System Considerations 3-34 AT27BV1024 |
|
|
Link URL |
| Cho đến nay ALLDATASHEET có giúp ích cho doanh nghiệp của bạn hay không? [ DONATE ] |
Alldatasheet là | Quảng cáo | Liên lạc với chúng tôi | Chính sách bảo mật | Liên kết đến bảng dữ liệu | Trao đổi link | Tìm kiếm theo nhà sản xuất All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |