TMS320VC5470ZHKA datasheet(24/94 Pages) TI

24 / 94 page

DSP Subsystem Functional Overview

December 2001 − Revised December 2002

SPRS017B

3.2.5 DSP Extended Program Memory

The DSP subsystem includes a memory paging scheme to extend the number of addressable program space

locations from 64K to 1M words. The four extended address pins (DSP_A16 to DSP_A19) are used to address

15 pages of program memory. Each page includes 64K addressable locations. The extended program

addresses are supported by eight instructions: FB[D], FBACC[D], FCALA[D], FCALL[D], FRET[D],

FRETE[D], READA, and WRITA.

•

FB[D] – Far branch

•

FBACC[D] – Far branch to the location specified by the value in accumulator A or accumulator B

•

FCALA[D] – Far call to the location specified by the value in accumulator A or accumulator B

•

FCALL[D] – Far call

•

FRET[D] – Far return

•

FRETE[D] – Far return with interrupts enabled

•

READA – Read program memory addressed by accumulator A and store in data memory

•

WRITA – Write data to program memory addressed by accumulator A

For more information on these instructions, please refer to the TMS320C54x DSP Reference Set, Volume 2:

Mnemonic Instruction Set (literature number SPRU172).

When the OVLY bit is set, each page of program memory is made up of two parts: a common block of

24K words maximum and a unique block of 40K words minimum. The common block is shared by all pages,

and each unique block is accessible only through its assigned page.

The value of the program counter extension register (XPC) defines the page selection. At a hardware reset,

the XPC is initialized to 0.

0 0000

1 0000

1 5FFF

Page 1

Lower 24K†

External

2 0000

2 5FFF

Page 2

Lower 24K†

External

. . .

F 0000

F 5FFF

Page 15

Lower 24K†

External

Page 0

64K

1 6000

2 6000

F 6000

Page 0

64K

Page 1

Upper 40K

External

Page 2

Upper 40K

External

. . .

Page 15

Upper 40K

External

0 FFFF

1 FFFF

2 FFFF

F FFFF

† Accesses to the lower 24K words of pages 1 through 15 are to external program memory only when the OVLY bit is cleared to 0. If the OVLY bit

is set to 1, on-chip RAM is mapped to 0x0 to 0x5FFF of pages 1 through 15. Note external address pins are provided to support 15 external pages.

Figure 3−4. DSP Extended Program Memory Map

3.2.6 DSP Relocatable Interrupt Vector Table

The reset, interrupt, and trap vectors are addressed in program space. These vectors are soft — meaning

that the processor, when taking the trap, loads the program counter (PC) with the trap address and executes

the code at the vector location. Four words are reserved at each vector location to accommodate a delayed

branch instruction, either two 1-word instructions or one 2-word instruction, which allows branching to the

appropriate interrupt service routine with minimal overhead.

TMS320VC5470ZHKA bảng dữ liệu(PDF) 24 Page - Texas Instruments

TMS320VC5470ZHKA bảng dữ liệu(HTML) 24 Page - Texas Instruments

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94

bảng dữ liệu tải về

Link URL