ABSOLUTE MAXIMUM RATINGS

Storage Temperature

HOW TO ORDER HGXOHT SURFACE MOUNT CRYSTAL OSCILLATORS

HGXOHT

4

D

S

N

SM3

20.0M ,

/

/

200

/

H

STATEK CORPORATION 512 N. MAIN ST., ORANGE, CA 92868 714-639-7810 FAX: 714-997-1256 www.statek.com

10208 Rev B

SPECIFICATIONS

Specifications are subject to change without notice. Tighter

specifications available, please contact factory.

Supply Voltage

3.3 V ±10%

5.0 V ±10%

Calibration Tolerance

± 50 ppm, or tighter as required

Frequency Stability

15 pF

Start-up Time

5 ms MAX

Rise/Fall Time

10 ns MAX

Duty Cycle

40% MIN, 60% MAX

Up to 100,000 g, 0.5 ms, ½ sine

20 g, 10-2000 Hz, swept sine

-55ºC up to 200ºC

1. Does not include calibration tolerance.

2. Frequency over temperature relative to nominal frequency.

3. Higher CMOS loads available. Contact factory.

4. Shock survival applies at -55ºC to +125ºC.

5. Per MIL-STD-202G, Method 204D, Condition D, Random vibration testing also available.

6. Expected life at 200ºC is in excess of 1,500 hours.

PACKAGING OPTIONS

HGXOHT - Tray Pack

- Tape and Reel

- 16 mm tape, 7” or 13” reels

Per EIA 481 (see Tape and Reel data

sheet # 10109)

Frequency

K = kHz

M = MHz

Termination

Blank = SM1

=Gold Plated (Pb Free)

SM3 = Solder Dipped

SM5 = Solder Dipped (Pb Free)

Shock Level

A = 5,000 g

B = 10,000 g

C = 20,000 g

D = 30,000 g

F = 50,000 g

G = 75,000 g

H = 100,000 g

Supply Voltage

4 = 3.3V

5 = 5.0V

Note: The HGXOHT oscillator with SM1 or SM5

termination is Pb free. The HGXOHT oscillator

with SM3 termination contains Pb.

Enable/Disable

Option

E or N

Blank = Standard

S = Special or

custom

ENABLE/DISABLE OPTIONS (E/N)

Statek offers two enable/disable options: E and N. The E-

version has a Tri-State output and stops oscillating internally

when the output is put into the high Z state. The N-version

does not have PIN 1 connected internally and has no

enable/disable capability. The following table describes the

Enable/Disable option E.

COMPARISON OF

ENABLE/DISABLE OPTIONS E AND N

EN

When enabled (PIN 1 is high*)

Output

Freq. output

Freq. output

Oscillator

Oscillates

Oscillates

Current consumption

Normal

Normal

When disabled (PIN 1 is low)

Output

High Z state

N/C

Oscillator

Stops

N/C

Current consumption

Very low

N/C

Frequency

Stability over

Temp. Range

(in ppm)

50

/

175

/

/

H

Temp. Range:

S = Customer

Specified Temp.

Range

Total

Frequency

Tolerance

(in ppm)

Calibration

Tolerance

(in ppm)

OR

Temp. Range:

S = Customer

Specified Temp.

Range

Total Frequency

Tolerance (in

ppm)

Calibration

Tolerance

(in ppm)

Frequency

Stability over

Temp. Range

(in ppm)

N/C Pin 1 not connected, output frequency.