| công cụ tìm kiếm bảng dữ liệu linh kiện điện tử |
|
A7986ATR bảng dữ liệu(PDF) 16 Page - STMicroelectronics |
|
|
|||||||||||||||||||||||||||||
A7986ATR bảng dữ liệu(HTML) 16 Page - STMicroelectronics |
|
16 / 42 page ![]() Application information A7986A 16/42 DocID022801 Rev 5 Equation 10 neglecting the small ESR of ceramic capacitors. Considering η = 1, this function has its maximum in D = 0.5, therefore, given the maximum peak-to-peak input voltage (VPP_MAX), the minimum input capacitor (CIN_MIN) value is: Equation 11 Typically, CIN is dimensioned to keep the maximum peak-to-peak voltage in the order of 1% of VINMAX. In the below table some multi-layer ceramic capacitors suitable for this device are reported: A ceramic bypass capacitor, as close to the VCC and GND pins as possible, so that additional parasitic ESR and ESL are minimized, is recommended in order to prevent instability on the output voltage due to noise. The value of the bypass capacitor can go from 100 nF to 1 µF. 6.2 Inductor selection The inductance value fixes the current ripple flowing through the output capacitor. So the minimum inductance value, in order to have the expected current ripple, must be selected. The rule to fix the current ripple value is to have a ripple at 20% - 40% of the output current. In continuous current mode (CCM), the inductance value can be calculated by the following equation: Equation 12 where TON is the conduction time of the internal high-side switch and TOFF is the conduction time of the external diode (in CCM, FSW = 1/(TON + TOFF)). The maximum current ripple, at fixed VOUT, is obtained at maximum TOFF, that is at minimum duty cycle (see Section 6.1 to calculate minimum duty). So, fixing ΔIL = 20% to 30% of the maximum output current, the minimum inductance value can be calculated as: Table 6. Input MLCC capacitors Manufacture Series Cap value ( μF) Rated voltage (V) Taiyo Yuden UMK325BJ106MM-T 10 50 GMK325BJ106MN-T 10 35 Murata GRM32ER71H475K 4.7 50 C IN I O V PP F SW ⋅ --------------------------- 1 D η ---- – D D η ---- 1D – () ⋅ + ⋅ ⋅ = C IN_MIN I O 2V PP_MAX F SW ⋅⋅ ------------------------------------------------ = ΔI L V IN V OUT – L ------------------------------ T ON ⋅ V OUT V F + L ---------------------------- T OFF ⋅ == |
|
Link URL |
| Cho đến nay ALLDATASHEET có giúp ích cho doanh nghiệp của bạn hay không? [ DONATE ] |
Alldatasheet là | Quảng cáo | Liên lạc với chúng tôi | Chính sách bảo mật | Liên kết đến bảng dữ liệu | Trao đổi link | Tìm kiếm theo nhà sản xuất All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |